ISL54066_0911 Datasheet, PDF (5/14 Pages) Intersil Corporation – Negative Signal Swing, High Off-Isolation, Dual SPST Single Supply Switch

ISL54066
Electrical Specifications - 3V Supply Test Conditions: V+ = +2.7V to +3.3V, GND = 0V, V_{CTL_H} = 1.4V, V_{CTL_L} = 0.5V (Note 9),
Unless Otherwise Specified.
PARAMETER
TEST CONDITIONS
TEMP
MIN
MAX
(°C) (Notes 10, 11) TYP (Notes 10, 11) UNITS
ANALOG SWITCH CHARACTERISTICS
ON-Resistance, r_ON
V+ = 2.7V, I_OUT = 100mA, V_IN = (V+ - 6.5) to V+ 25
-
1.5
-
Ω
(See Figure 4)
Full
-
1.9
-
Ω
r_ON Matching Between Channels, V+ = 2.7V, I_OUT = 100mA, V_IN = Voltage at max
25
-
10
-
mΩ
Δr_ON
r_ON, (Note 13)
Full
-
10
-
mΩ
r_ON Flatness, R_FLAT(ON)
V+ = 2.7V, I_OUT = 100mA, V_IN = (V+ - 6.5) to V+ 25
(Notes 12, 14)
Full
-
0.63
1
Ω
-
0.68
1.35
Ω
DYNAMIC CHARACTERISTICS
Turn-ON Time, t_ON
V+ = 2.7V, V_IN = 1.5V, R_L = 50Ω, C_L = 35pF
25
-
60
-
ns
(See Figure 1)
Full
-
68
-
ns
Turn-OFF Time, t_OFF
V+ = 2.7V, V_IN = 1.5V, R_L = 50Ω, C_L = 35pF
25
-
31
-
ns
(See Figure 1)
Full
-
35
-
ns
Charge Injection, Q
OFF-Isolation
C_L = 1.0nF, V_G = 0V, R_G = 0Ω, (See Figure 2)
25
-
150
-
pC
R_L = 50Ω, C_L = 5pF, f = 1MHz, V_INx = 1V_RMS
25
-
70
-
dB
(See Figure 3)
Crosstalk (Channel-to-Channel)
R_L = 50Ω, C_L = 5pF, f = 1MHz, V_IN1 = 1V_RMS
25
-
-80
-
dB
(See Figure 5)
Total Harmonic Distortion
f = 20Hz to 20kHz, V_OUT = 2V_P-P, R_L = 32Ω
25
-
0.04
-
%
INx OFF Capacitance, C_OFF
f = 1MHz, GND1 = float (See Figure 6)
25
-
33
-
pF
OUTx ON Capacitance, C_OUT(ON) f = 1MHz, GND2 = float (See Figure 6)
25
-
124
-
pF
POWER SUPPLY CHARACTERISTICS
Positive Supply Current, I+
V+ = +3.6V, V_CTLx = 0V or V+
25
-
0.02
-
µA
Full
-
1.76
-
µA
DIGITAL INPUT CHARACTERISTICS
Input Voltage Low, V_{CTLx_L}
Input Voltage High, V_{CTLx_H}
Input Current, I_{CTLx_H}, I_{CTLx_L}
V+ = 3.3V, V_{CTL x} = 0V or V+
25
-
-
0.5
V
25
1.4
-
-
V
25
-0.5
-
0.5
µA
Full
-
0.55
-
µA
Electrical Specifications - 1.8V Supply Test Conditions: V+ = +1.8V, GND = 0V, V_{CTL_H} = 1.0V, V_{CTL_L} = 0.4V (Note 9),
Unless Otherwise Specified.
PARAMETER
TEST CONDITIONS
TEMP
MIN
MAX
(°C) (Notes 10, 11) TYP (Notes 10, 11) UNITS
ANALOG SWITCH CHARACTERISTICS
ON-Resistance, r_ON
V+ = 1.8V, I_OUT = 100mA, V_IN = (V+ - 6.5V) to V+, 25
-
3
-
Ω
(See Figure 4)
Full
-
3.2
-
Ω
r_ON Matching Between Channels, V+ = 1.8V, I_OUT = 100mA, V_IN = Voltage at max
25
-
20
-
mΩ
ΔR_ON
r_ON, (Note 13)
Full
-
20
-
mΩ
r_ON Flatness, R_FLAT(ON)
V+ = 1.8V, I_OUT = 100mA, V_IN = (V+ - 6.5) to V+, 25
-
2.3
-
Ω
(Note 12)
Full
-
2.5
-
Ω
5
FN6584.1
November 3, 2009