ISL3150E Datasheet, PDF (5/22 Pages) Intersil Corporation – ±16.5kV ESD, Large Output Swing, 5V, Full Fail-Safe, 1/8 Unit Load, RS-485/RS-422 Transceivers

ISL3150E, ISL3152E, ISL3153E, ISL3155E, ISL3156E, ISL3158E
Absolute Maximum Ratings
V_CC to Ground . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7V
Input Voltages
DI, DE, RE . . . . . . . . . . . . . . . . -0.3V to (V_CC + 0.3V)
Input/Output Voltages
A/Y, B/Z, A, B, Y, Z . . . . . . . . . . . . . . . . . -9V to +13V
A/Y, B/Z, A, B, Y, Z (Transient Pulse Through 100Ω,
Note 16) . . . . . . . . . . . . . . . . . . . . . . . . . . . ±100V
RO . . . . . . . . . . . . . . . . . . . . . . . -0.3V to (V_CC +0.3V)
Short Circuit Duration
Y, Z . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Continuous
ESD Rating . . . . . . . . . . . . . . . . . See Specification Table
Recommended Operating Conditions
Supply Voltage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5V
Temperature Range . . . . . . . . . . . . . . . . -40°C to +85°C
Bus Pin Common Mode Voltage Range . . . . . -7V to +12V
Thermal Information
Thermal Resistance (Typical, Note 5)
θ_JA (°C/W)
8 Ld SOIC . . . . . . . . . . . . . . . . .
105
8 Ld MSOP, PDIP* . . . . . . . . . . . .
140
10 Ld MSOP . . . . . . . . . . . . . . . .
130
14 Ld SOIC . . . . . . . . . . . . . . . .
130
Maximum Junction Temperature (Plastic Package) . +150°C
Maximum Storage Temperature Range . . -65°C to +150°C
Pb-Free Reflow Profile. . . . . . . . . . . . . . . . .see link below
http://www.intersil.com/pbfree/Pb-FreeReflow.asp
*Pb-free PDIPs can be used for through-hole wave solder
processing only. They are not intended for use in Reflow
solder processing applications.
CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact
product reliability and result in failures not covered by warranty.
NOTE:
5. θ_JA is measured with the component mounted on a high effective thermal conductivity test board in free air. See Tech Brief
TB379 for details.
Electrical Specifications
Test Conditions: V_CC = 4.5V to 5.5V; Unless Otherwise Specified. Typicals are at V_CC = 5V,
T_A = +25°C (Note 6). Boldface limits apply over the operating temperature range,
-40°C to +85°C.
PARAMETER
SYMBOL
TEST CONDITIONS
TEMP MIN
MAX
(°C) (Note 14) TYP (Note 14) UNITS
DC CHARACTERISTICS
Driver Differential V_OUT
(No load)
V_OD1
Full
-
-
V_CC
V
Driver Differential V_OUT
(Loaded)
V_OD2 R_L = 100Ω (RS-422) (Figure 1A)
Full
2.8
3.6
-
V
R_L = 54Ω (RS-485) (Figure 1A)
Full
2.4
3.1
V_CC
V
R_L = 15Ω (Eight 120Ω terminations) 25
-
1.65
-
V
(Note 15)
R_L = 60Ω, -7V ≤ V_CM ≤ 12V
(Figure 1B)
Full
2.4
3
-
V
Change in Magnitude of
Driver Differential V_OUT for
Complementary Output
States
ΔV_OD R_L = 54Ω or 100Ω (Figure 1A)
Full
-
0.01
0.2
V
Driver Common-Mode V_OUT
Change in Magnitude of
Driver Common-Mode V_OUT
for Complementary Output
States
V_OC
ΔV_OC
R_L = 54Ω or 100Ω (Figure 1A)
R_L = 54Ω or 100Ω (Figure 1A)
Full
-
-
3.15
V
Full
-
0.01
0.2
V
Logic Input High Voltage
V_IH
DE, DI, RE
Full
2
-
-
V
Logic Input Low Voltage
V_IL
DE, DI, RE
Full
-
-
0.8
V
DI Input Hysteresis Voltage
V_HYS
25
-
100
-
mV
Logic Input Current
I_IN1
DE, DI, RE
Full
-2
-
2
µA
Input Current (A, B, A/Y,
B/Z)
I_IN2
DE = 0V, V_CC = 0V or V_IN = 12V
Full
-
70
125
µA
5.5V
V_IN = -7V
Full
-75
55
-
µA
5
FN6363.2
July 30, 2009