DG181 Datasheet, PDF (5/9 Pages) Intersil Corporation – High-Speed Drivers with JFET Switch

DG181 Series
Electrical Specifications V+ = +15V, V- = -15V, V_L = 5V, Unless Otherwise Specified (Continued)
PARAMETER
SUPPLY
DEVICE
NUMBER
(NOTE 1)
TEST CONDITIONS
A SERIES
B SERIES
-55^oC +25^oC +125^oC -20^oC +25^oC +85^oC
I+
I-
I_L
I_GND
I+
I-
DG181, DG182,
DG190, DG191
DG184, DG185
DG187, DG188
DG181, DG182,
DG190, DG191
DG184, DG185
DG187, DG188
DG181, DG182,
DG184, DG185,
DG190, DG191
DG187, DG188
All
DG181, DG182,
DG190, DG191
DG184, DG185
DG187, DG188
DG181, DG182,
DG190, DG191
V_IN = 5V
V_IN = 0V
-
1.5
-
-
0.1
-
-
0.8
-
-
-5.0
-
-
-4.0
-
-
-3.0
-
-
4.5
-
-
3.2
-
-
-2.0
-
-
1.5
-
-
3.0
-
-
0.8
-
-
-5.0
-
-
1.5
-
-
0.1
-
-
0.8
-
-
-5.0
-
-
-4.0
-
-
-3.0
-
-
4.5
-
-
3.2
-
-
-2.0
-
-
1.5
-
-
3.0
-
-
0.8
-
-
-5.0
-
DG184, DG185
DG187, DG188
I_L
DG181, DG182,
DG184, DG185,
DG190, DG191
-
-5.5
-
-
-3.0
-
-
4.5
-
-
-5.5
-
-
-3.0
-
-
4.5
-
DG187, DG188
-
3.2
-
I_GND
All
NOTE:
-
-2.0
-
1. See Switching State Diagrams for V_IN “ON” and V_IN “OFF” Test Conditions.
-
3.2
-
-
-2.0
-
UNITS
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
Electrical Specifications Maximum Resistances (R_DS(ON) MAX)
DEVICE
NUMBER
DG181
DG182
DG184
DG185
DG187
DG188
DG190
DG191
NOTES:
TEST CONDITIONS (NOTE 1)
V+ = 15V, V- = -15V, V_L = 5V
V_D = -7.5V
I_S = -10mA, V_IN = “ON”
V_D = -10V
V_D = -7.5V
V_D = -10V
V_D = -7.5V
V_D = -10V
V_D = -7.5V
V_D = -10V
MILITARY
TEMPERATURE
-55^oC +25^oC +125^oC
30
30
60
75
75
100
30
30
60
75
75
150
30
30
60
75
75
150
30
30
60
75
75
150
INDUSTRIAL
TEMPERATURE
-20^oC +25^oC +85^oC
50
50
75
100
100
150
50
50
75
100
100
150
50
50
75
100
100
150
50
50
75
100
100
150
UNITS
Ω
Ω
Ω
Ω
Ω
Ω
Ω
Ω
1. See Switching State Diagrams for V_IN “ON” and V_IN “OFF” Test Conditions.
2. Normally the minimum signal handling capability of the DG181 thru DG191 family is 20V peak to peak for the 75Ω switches and 15V peak-
to-peak for the 30Ω (refer I_D and I_S tests above).
3. For other Analog Signals, the following guidelines can be used: proper switch turn-off requires that V- ≤ V_ANALOG(peak) - V_P where V_P =
7.5V for the 80Ω switches and V_P = 5.0V for 75Ω switches e.g., - 10V minimum (-peak) analog signal and a 75Ω switch (V_P = 5V), requires
that V- ≤ -10V -5V = -15V.
5