CD4046BMS Datasheet, PDF (5/11 Pages) Intersil Corporation – CMOS Micropower Phase Locked Loop

Specifications CD4046BMS
TABLE 3. ELECTRICAL PERFORMANCE CHARACTERISTICS (Continued)
LIMITS
PARAMETER
SYMBOL
CONDITIONS
Quiescent Leakage
Phase Comparator
(Bias Amp Leakage)
BIAS LKG VDD = 5
VIN =
VDD or
GND
Pin 14 Open
Pin 5 = VDD
Pin 14 = VSS or VDD
Pin 5 = VDD
VDD = 10 Pin 14 Open
VIN =
Pin 5 = VDD
VDD or
GND
Pin 14 = VSS or VDD
Pin 5 = VDD
VDD = 15 Pin 14 Open
VIN =
Pin 5 = VDD
VDD or
GND
Pin 14 = VSS or VDD
Pin 5 = VDD
AC Coupled Signal In-
put Voltage Sensitivity
(Peak to Peak)
VS VDD = 10V, Input Frequency =
100kHz Sine Wave
VDD = 15V, Input Frequency =
100kHz Sine Wave
NOTES TEMPERATURE MIN
1, 2
+25^oC/-55^oC
-
1, 2
+25^oC/-55^oC
-
1, 2
+25^oC/-55^oC
-
1, 2
+25^oC/-55^oC
-
1, 2
+25^oC/-55^oC
-
1, 2
+25^oC/-55^oC
-
1, 2
+25^oC
-
1, 2
+25^oC
-
MAX
0.2
UNITS
mA
20
µA
1.0
mA
40
µA
1.5
mA
80
µA
660
mV
1800
mV
NOTES:
1. All voltages referenced to device GND.
2. The parameters listed on Table 3 are controlled via design or process and are not directly tested. These parameters are characterized
on initial design release and upon design changes which would affect these characteristics.
TABLE 4. POST IRRADIATION ELECTRICAL PERFORMANCE CHARACTERISTICS
LIMITS
PARAMETER
SYMBOL
CONDITIONS
Supply Current
IDD VDD = 20V, VIN = VDD or GND
N Threshold Voltage
VNTH VDD = 10V, ISS = -10µA
N Threshold Voltage
Delta
∆VTN VDD = 10V, ISS = -10µA
P Threshold Voltage
VTP VSS = 0V, IDD = 10µA
P Threshold Voltage
Delta
∆VTP VSS = 0V, IDD = 10µA
Functional
F
VDD = 18V, VIN = VDD or GND
VDD = 3V, VIN = VDD or GND
AC Coupled Signal Input
Voltage Sensitivity
VS VDD = 5V
Input Frequency = 100kHz
Sine Wave
NOTES
1, 4
1, 4
1, 4
1, 4
1, 4
1
1, 2, 3
TEMPERATURE MIN
+25^oC
-
+25^oC
-2.8
+25^oC
-
MAX
25
-0.2
±1
+25^oC
+25^oC
0.2
2.8
-
±1
+25^oC
+25^oC
VOH > VOL <
VDD/2 VDD/2
-
1.35 x
+25^oC
Limit
NOTES: 1. All voltages referenced to device GND.
2. Go/No Go test with limits applied to inputs.
3. See Table 2 for +25^oC limit.
UNITS
µA
V
V
V
V
V
mV
TABLE 5. BURN-IN AND LIFE TEST DELTA PARAMETERS +25^OC
PARAMETER
SYMBOL
DELTA LIMIT
Supply Current - MSI-2
Output Current (Sink)
Output Current (Source)
IDD
IOL5
IOH5A
± 1.0µA
± 20% x Pre-Test Reading
± 20% x Pre-Test Reading
7-890