ISL72028SEH Datasheet, PDF (4/19 Pages) Intersil Corporation – 3.3V Radiation Tolerant CAN Transceiver, 1Mbps, Low Power Shutdown, Split Termination Output

ISL72028SEH
Absolute Maximum Ratings
VCC to GND With/Without Ion Beam . . . . . . . . . . . . . . . . . . . . -0.3V to 4.5V
CANH, CANL, VREF Under Ion Beam . . . . . . . . . . . . . . . . . . . . . . . . . . . ±18V
CANH, CANL, VREF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±20V
I/O Voltages
D, R, RS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.5V to 7V
Receiver Output Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . -10mA to 10mA
Output Short-Circuit Duration . . . . . . . . . . . . . . . . . . . . . . . . . . . . Continuous
ESD Rating:
Human Body Model
CANH, CANL Bus Pins (Tested per MIL-PRF-883 3015.7) . . . . . . . 4kV
All Other Pins (Tested per MIL-PRF-883 3015.7) . . . . . . . . . . . . . . 4kV
Charged Device Model (Tested per JESD22-C101D) . . . . . . . . . . . . 750V
Machine Model (Tested per JESD22-A115-A) . . . . . . . . . . . . . . . . . . 200V
Thermal Information
Thermal Resistance (Typical)
_JA (°C/W) _JC (°C/W)
8 Ld FP Package (Notes 3, 4) Direct Attach. .
39
7
Maximum Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . .+175°C
Storage Temperature Range. . . . . . . . . . . . . . . . . . . . . . . .-65°C to +150°C
Recommended Operating Conditions
Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .-55°C to +125°C
V_CC Supply Voltage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.0V to 3.6V
Voltage on CAN I/O. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .-7V to 12V
V_IH D Logic Pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2V to 5.5V
V_IL D Logic Pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0V to 0.8V
I_OH Driver (CANH - CANL = 1.5V, V_CC = 3.3V) . . . . . . . . . . . . . . . . . . - 40mA
I_OH Receiver (V_OH = 2.4V) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -4mA
I_OL Driver (CANH - CANL = 1.5V, V_CC = 3.3V) . . . . . . . . . . . . . . . . . . +40mA
I_OL Receiver (V_OL = 0.4V). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +4mA
CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product
reliability and result in failures not covered by warranty.
NOTES:
3. _JA is measured with the component mounted on a high effective thermal conductivity test board (two buried 1oz copper planes) with “direct attach”
features package base mounted to PCB thermal land with a 10mil gap fill material having a k of 1W/m-K. See Tech Brief TB379.
4. For _JC, the “case temp” location is the center of the package underside.
Electrical Specifications Test Conditions: V_CC = 3.0V to 3.6V; Typicals are at T_A = +25°C (Note 7); unless otherwise specified (Note 5).
Boldface limits apply across the operating temperature range, -55°C to +125°C or over a total ionizing dose of 75krad(Si) at +25°C with exposure at a
low dose rate of <10mrad(Si)/s.
PARAMETER
SYMBOL
TEST CONDITIONS
TEMP MIN
TYP
MAX
(°C) (Note 6) (Note 7) (Note 6) UNIT
DRIVER ELECTRICAL CHARACTERISTICS
Dominant Bus Output Voltage
V_O(DOM)
D = 0V, CANH, RS = 0V,
Figures 10 and 11
3.0V ≤ V_CC ≤ 3.6V Full 2.25
2.85
V_CC
V
D = 0V, CANL, RS = 0V, Figures 10
and 11
Full 0.10 0.65 1.25 V
Recessive Bus Output Voltage
V_O(REC)
D = 3V, CANH, RS = 0V, 60Ωand 3.0V ≤ V_CC ≤ 3.6V Full 1.80
no load, Figures 10 and 11
2.30
2.70 V
D = 3V, CANL, RS = 0V, 60Ωand
no load, Figures 10 and 11
Full 1.80 2.30 2.80 V
Dominant Output Differential
Voltage
Recessive Output Differential
Voltage
Logic Input High Voltage (D)
Logic Input Low Voltage (D)
High Level Input Current (D)
Low Level Input Current (D)
RS Input Voltage for Low Power
Shutdown Mode
V_OD(DOM) D = 0V, RS = 0V, 3.0V ≤ V_CC ≤ 3.6V, Figures 10 and 11 Full 1.5
2.2
D = 0V, RS = 0V, 3.0V ≤ V_CC ≤ 3.6V, Figures 11 and 12 Full 1.2
2.1
V_OD(REC) D = 3V, RS = 0V, 3.0V ≤ V_CC ≤ 3.6V, Figures 10 and 11 Full -120
0.2
D = 3V, RS = 0V, 3.0V ≤ V_CC ≤ 3.6V, no load
Full -500
-34
V_IH
3.0V ≤ V_CC ≤ 3.6V, Note 8
Full 2.0
-
V_IL
3.0V ≤ V_CC ≤ 3.6V, Note 8
Full
0
-
I_IH
D = 2.0V, 3.0V ≤ V_CC ≤ 3.6V
Full -30
-3
I_IL
D = 0.8V, 3.0V ≤ V_CC ≤ 3.6V
Full -30
-7
V_IN(RS)
3.0V ≤ V_CC ≤ 3.6V
Full 0.75xV_CC 1.9
3.0
V
3.0
V
12 mV
50 mV
5.5
V
0.8
V
30 µA
30 µA
5.5
V
Submit Document Feedback
4
FN8764.1
November 9, 2015