English
Language : 

ISL43L710 Datasheet, PDF (4/11 Pages) Intersil Corporation – Ultra Low ON-Resistance, Single Supply, Differential SPST Analog Switches
◁
ISL43L710, ISL43L711, ISL43L712
Electrical Specifications - 3V Supply Test Conditions: V+ = +2.7V to +3.3V, GND = 0V, VINH = 1.4V, VINL = 0.5V (Note 7),
Unless Otherwise Specified (Continued)
PARAMETER
TEST CONDITIONS
TEMP
MIN
MAX
(°C) (Notes 8, 9) TYP (Notes 8, 9) UNITS
POWER SUPPLY CHARACTERISTICS
Power Supply Range
Full
1.65
-
3.6
V
Positive Supply Current, I+
V+ = 1.65V to 3.6V, VIN = 0V or V+, all channels on 25
-
or off
Full
-
-
30
nA
-
750
nA
DIGITAL INPUT CHARACTERISTICS
Input Voltage Low, VINL
Full
-
-
0.5
V
Input Voltage High, VINH
Full
1.4
-
-
V
Input Current, IINH, IINL
V+ = 3.3V, VIN = 0V or V+ (Note 10)
Full
-0.5
-
0.5
μA
NOTES:
7. VIN = input voltage to perform proper function.
8. The algebraic convention, whereby the most negative value is a minimum and the most positive a maximum, is used in this data sheet.
9. Parameters with MIN and/or MAX limits are 100% tested at +25°C, unless otherwise specified. Temperature limits established by characterization
and are not production tested.
10. Limits established by characterization and are not production tested.
11. RON matching between channels is calculated by subtracting the channel with the highest max Ron value from the channel with lowest max Ron
value.
12. Flatness is defined as the difference between maximum and minimum value of on-resistance over the specified analog signal range.
Electrical Specifications - 1.8V Supply
Test Conditions: V+ = +1.65V to +2.0V, GND = 0V, VINH = 1.0V, VINL = 0.4V (Note 7),
Unless Otherwise Specified
PARAMETER
TEST CONDITIONS
TEMP
MIN
MAX
(°C) (Notes 8, 9) TYP (Notes 8, 9) UNITS
ANALOG SWITCH CHARACTERISTICS
Analog Signal Range, VANALOG
Full
0
-
V+
V
ON Resistance, RON
V+ = 1.8V, ICOM = 100mA, VNO or VNC = 0V to V+, 25
-
0.26
0.35
Ω
(See Figure 4, Note 10)
Full
-
-
0.4
Ω
RON Matching Between Channels, V+ = 1.8V, ICOM = 100mA, VNO or VNC = Voltage at 25
-
0.005
-
Ω
ΔRON
Max RON, (Note 11)
Full
-
0.005
-
Ω
RON Flatness, RFLAT(ON)
V+ = 1.8V, ICOM = 100mA, VNO or VNC = 0V to V+, 25
-
0.074
-
Ω
(Note 12)
Full
-
0.082
-
Ω
NO or NC OFF Leakage Current, V+ = 2.0V, VCOM = 0.3V, 1.8V, VNO or VNC = 1.8V,
25
-3
-
3
nA
INO(OFF) or INC(OFF)
0.3V
Full
-60
-
60
nA
COM ON Leakage Current,
V+ = 2.0V, VCOM = 0.3V, 1.8V, or VNO or VNC = 0.3V, 25
-3
-
3
nA
ICOM(ON)
1.8V
Full
-80
-
80
nA
DYNAMIC CHARACTERISTICS
Turn-ON Time, tON
V+ = 1.65V, VNO or VNC = 1.0V, RL = 50Ω, CL =
25
-
35pF, VIN = 0 to 1.65V, (See Figure 1, Note 10)
Full
-
30
40
ns
-
45
ns
Turn-OFF Time, tOFF
V+ = 1.65V, VNO or VNC = 1.0V, RL = 50Ω, CL =
25
-
35pF, VIN = 0 to 1.65V, (See Figure 1, Note 10)
Full
-
25
35
ns
-
40
ns
Charge Injection, Q
CL = 1.0nF, VG = 0V, RG = 0Ω, (See Figure 2)
25
-
-80
-
pC
OFF Isolation
RL = 50Ω, CL = 5pF, f = 100kHz, VCOM = 1 VRMS,
25
-
62
-
dB
Crosstalk (Channel-to-Channel)
(See Figure 3 and Figure 5)
25
-
-94
-
dB
4
FN6092.3
May 29, 2008
 ▷