English
Language : 

ISL43L710 Datasheet, PDF (3/11 Pages) Intersil Corporation – Ultra Low ON-Resistance, Single Supply, Differential SPST Analog Switches
◁
ISL43L710, ISL43L711, ISL43L712
Absolute Maximum Ratings
V+ to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3 to 4.7V
Input Voltages
IN (Note 5) . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3 to ((V+) + 0.3V)
NO, NC (Note 5) . . . . . . . . . . . . . . . . . . . . . . . -0.3 to ((V+) + 0.3V)
Output Voltages
COM (Note 5). . . . . . . . . . . . . . . . . . . . . . . . . . -0.3 to ((V+) + 0.3V)
Continuous Current (Any Terminal) . . . . . . . . . . . . . . . . . . . . 300mA
Peak Current, IN, NO, NC, or COM
(Pulsed 1ms, 10% Duty Cycle, Max) . . . . . . . . . . . . . . . . . . . 500mA
ESD Rating (Per MIL-STD-883 Method 3015). . . . . . . . . . . . . .>8kV
Thermal Information
Thermal Resistance (Typical, Note 6)
θJA (°C/W)
8 Ld 3x3 thin DFN Package . . . . . . . . . . . . . . . . . . .
110
8 Ld MSOP Package . . . . . . . . . . . . . . . . . . . . . . . .
190
Maximum Junction Temperature (Plastic Package). . . . . . . +150°C
Maximum Storage Temperature Range . . . . . . . . . . . -65°C to +150°C
Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . +300°C
(Lead Tips Only)
Operating Conditions
Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . .-40°C to +85°C
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTES:
5. Signals on NC, NO, COM, or IN exceeding V+ or GND are clamped by internal diodes. Limit forward diode current to maximum current ratings.
6. θJA is measured with the component mounted on a low effective thermal conductivity test board in free air. See Tech Brief TB379 for details.
Electrical Specifications - 3V Supply Test Conditions: V+ = +2.7V to +3.3V, GND = 0V, VINH = 1.4V, VINL = 0.5V (Note 7),
Unless Otherwise Specified
PARAMETER
TEST CONDITIONS
TEMP
MIN
MAX
(°C) (Notes 8, 9) TYP (Notes 8, 9) UNITS
ANALOG SWITCH CHARACTERISTICS
Analog Signal Range, VANALOG
Full
0
-
V+
V
ON Resistance, RON
V+ = 2.7V, ICOM = 100mA, VNO or VNC = 0V to V+ 25
-
0.17
0.25
Ω
(See Figure 4)
Full
-
-
0.3
Ω
RON Matching Between Channels, V+ = 2.7V, ICOM = 100mA, VNO or VNC = Voltage at 25
-
0.005
0.02
Ω
ΔRON
Max RON, (Note 11)
Full
-
-
0.04
Ω
RON Flatness, RFlat(ON)
V+ = 2.7V, ICOM = 100mA, VNO or VNC = 0V to V+, 25
-
0.008
0.06
Ω
(Note 12)
Full
-
-
0.07
Ω
NO or NC OFF Leakage Current, V+ = 3.3V, VCOM = 0.3, 3V, VNO or VNC = 3V, 0.3V 25
-3
-
INO(OFF) or INC(OFF)
Full
-60
-
3
nA
60
nA
COM ON Leakage Current,
ICOM(ON)
V+ = 3.3V, VCOM = 0.3V, 3V, or VNO or VNC = 0.3V, 25
-3
-
3V
Full
-80
-
3
nA
80
nA
DYNAMIC CHARACTERISTICS
Turn-ON Time, tON
V+ = 2.7V, VNO or VNC = 1.5V, RL = 50Ω, CL = 35pF, 25
-
VIN = 0 to 2.7V, (See Figure 1, Note 10)
Full
-
15
25
ns
-
30
ns
Turn-OFF Time, tOFF
V+ = 2.7V, VNO or VNC = 1.5V, RL = 50Ω, CL = 35pF, 25
-
VIN = 0 to 2.7V, (See Figure 1, Note 10)
Full
-
15
25
ns
-
30
ns
Charge Injection, Q
OFF Isolation
CL = 1.0nF, VG = 0V, RG = 0Ω, (See Figure 2)
25
-
-125
-
pC
RL = 50Ω, CL = 5pF, f = 100kHz, VCOM = 1 VRMS,
25
-
62
-
dB
(See Figure 3)
Crosstalk (Channel-to-Channel)
RL = 50Ω, CL = 5pF, f = 100kHz, VCOM = 1 VRMS,
25
-
-94
-
dB
(See Figure 5)
NO or NC OFF Capacitance, COFF f = 1MHz, VNO or VNC = VCOM = 0V, (See Figure 6) 25
-
182
-
pF
COM OFF Capacitance, CCOM(OFF) f = 1MHz, VNO or VNC = VCOM = 0V, (See Figure 6) 25
-
182
-
pF
COM ON Capacitance, CCOM(ON) f = 1MHz, VNO or VNC = VCOM = 0V, (See Figure 6) 25
-
290
-
pF
3
FN6092.3
May 29, 2008
 ▷