English
Language : 

ISL43L210 Datasheet, PDF (4/12 Pages) Intersil Corporation – Ultra Low ON-Resistance, +1.1V to +4.5V Single Supply, SPDT Analog Switch
◁
ISL43L210
Electrical Specifications - 4.3V Supply
Test Conditions: V+ = +3.9V to +4.5V, GND = 0V, VINH = 1.6V, VINL = 0.5V (Notes 4, 6),
Unless Otherwise Specified (Continued)
PARAMETER
TEST CONDITIONS
TEMP (NOTE 5)
(NOTE 5)
(°C)
MIN
TYP
MAX UNITS
Total Harmonic Distortion
f = 20Hz to 20kHz, VCOM = 2VP-P, RL = 32Ω
25
NO or NC OFF Capacitance, COFF f = 1MHz, VNO or VNC = VCOM = 0V, (See Figure 7)
25
COM ON Capacitance, CCOM(ON) f = 1MHz, VNO or VNC = VCOM = 0V, (See Figure 7)
25
POWER SUPPLY CHARACTERISTICS
-
0.006
-
%
-
40
-
pF
-
100
-
pF
Power Supply Range
Full
1.1
-
4.5
V
Positive Supply Current, I+
V+ =+4.5V, VIN = 0V or V+
25
-
Full
-
-
0.05
µA
-
0.4
µA
DIGITAL INPUT CHARACTERISTICS
Input Voltage Low, VINL
Full
-
-
0.5
V
Input Voltage High, VINH
Full
1.6
-
-
V
Input Current, IINH, IINL
V+ = 4.5V, VIN = 0V or V+ (Note 8)
Full
-0.5
-
0.5
µA
NOTES:
4. VIN = input voltage to perform proper function.
5. The algebraic convention, whereby the most negative value is a minimum and the most positive a maximum, is used in this data sheet.
6. Parts are 100% tested at +25°C. Limits across the full temperature range are guaranteed by design and correlation.
7. Flatness is defined as the difference between maximum and minimum value of on-resistance over the specified analog signal range.
8. Guaranteed but not tested.
Electrical Specifications - 3V Supply
Test Conditions: V+ = +2.7V to +3.6V, GND = 0V, VINH = 1.4V, VINL = 0.5V (Notes 4, 6),
Unless Otherwise Specified
PARAMETER
TEST CONDITIONS
TEMP (NOTE 5)
(NOTE 5)
(°C)
MIN
TYP
MAX UNITS
ANALOG SWITCH CHARACTERISTICS
Analog Signal Range, VANALOG
ON Resistance, RON
V+ = 2.7V, ICOM = 100mA, VNO or VNC = 1.5V
(See Figure 5)
Full
0
-
V+
V
25
-
0.44
0.6
Ω
Full
-
-
0.7
Ω
RON Matching Between Channels, V+ = 2.7V, ICOM = 100mA, VNO or VNC = 1.5V
∆RON
25
-
0.005
0.03
Ω
Full
-
-
0.05
Ω
RON Flatness, RFLAT(ON)
V+ = 2.7V, ICOM = 100mA, VNO or VNC = 0.6V, 1.5V,
25
-
0.06
0.1
Ω
2.1V (Note 7)
Full
-
-
0.12
Ω
NO or NC OFF Leakage Current, V+ = 3.3V, VCOM = 0.3V, 3V, VNO or VNC = 3V, 0.3V
25
-
0.9
-
nA
INO(OFF) or INC(OFF)
Full
-
8
-
nA
COM ON Leakage Current,
ICOM(ON)
V+ = 3.3V, VCOM = 0.3V, 3V, or VNO or VNC = 0.3V, 3V, 25
-
0.9
-
nA
or Floating
Full
-
17
-
nA
DYNAMIC CHARACTERISTICS
Turn-ON Time, tON
V+ = 2.7V, VNO or VNC = 1.5V, RL = 50Ω, CL = 35pF
25
-
(See Figure 1, Note 8)
Full
-
8
15
ns
-
20
ns
Turn-OFF Time, tOFF
V+ = 2.7V, VNO or VNC = 1.5V, RL = 50Ω, CL = 35pF
25
-
(See Figure 1, Note 8)
Full
-
4
10
ns
-
15
ns
Break-Before-Make Time Delay, tD V+ = 3.0V, VNO or VNC = 1.5V, RL = 50Ω, CL = 35pF Full
1
4
-
ns
(See Figure 3, Note 8)
4
FN6131.0
March 15, 2005
 ▷