English
Language : 

ISL43240_14 Datasheet, PDF (4/15 Pages) Intersil Corporation – Low-Voltage, Single and Dual Supply, Quad SPDT, High Performance Analog Switch
◁
ISL43240
Electrical Specifications ±5V Supply Test Conditions: VSUPPLY = 4.5V to 5.5V, GND = 0V, VINH = 2.4V, VINL = 0.8V (Note 7),
Unless Otherwise Specified (Continued)
PARAMETER
TEST CONDITIONS
TEMP
MIN
MAX
(°C) (Note 8) TYP (Note 8)
POWER SUPPLY CHARACTERISTICS
Power Supply Range
Full
2
-
6
Positive Supply Current, I+
VS = 5.5V, VIN = 0V or V+, Switch On or Off
25
-1
0.01
1
Full
-1
-
1
Negative Supply Current, I-
25
-1
0.01
1
Full
-1
-
1
NOTES:
8. VIN = Input voltage to perform proper function.
9. The algebraic convention, whereby the most negative value is a minimum and the most positive a maximum, is used in this data sheet.
10. Leakage parameter is 100% tested at high temp, and guaranteed by correlation at +25°C.
11. Flatness is defined as the delta between the maximum and minimum rON values over the specified voltage range.
12. Between any two switches.
UNITS
V
µA
µA
µA
µA
Electrical Specifications 5V Supply Test Conditions: V+ = +4.5V to +5.5V, V- = GND = 0V, VINH = 2.4V, VINL = 0.8V (Note 7),
Unless Otherwise Specified
PARAMETER
TEST CONDITIONS
TEMP
MIN
MAX
(°C) (Note 8) TYP (Note 8) UNITS
ANALOG SWITCH CHARACTERISTICS
Analog Signal Range, VANALOG
ON-resistance, rON
V+ = 4.5V, ICOM = 1.0mA, VNO or VNC = 3.5V,
See Figure 5
Full
0
25
-
Full
-
-
V+
V
30
40
Ω
-
50
Ω
rON Matching Between Channels,
rON
V+ = 4.5V, ICOM = 1.0mA, VNO or VNC = 3V
25
-
0.5
3
Ω
Full
-
-
4
Ω
rON Flatness, RFLAT(ON)
V+ = 5.5V, ICOM = 1.0mA, VNO or VNC = 1V, 2V, 3V,
Note 10
25
-
4.4
6
Ω
Full
-
-
8
Ω
NO or NC OFF Leakage Current,
V+ = 5.5V, VCOM = 1V, 4.5V, VNO or VNC = 4.5V, 1V, Note 9 25
-0.2
-
0.2
nA
INO(OFF) or INC(OFF)
Full
-2.5
-
2.5
nA
COM ON Leakage Current, ICOM(ON) V+ = 5.5V, VCOM = 1V, 4.5V, VNO or VNC = 1V, 4.5V Note 9 25
-0.4
-
0.4
nA
Full
-5
-
5
nA
DIGITAL INPUT CHARACTERISTICS
Input Voltage High, VINH
Input Voltage Low, VINL
Input Current, IINH, IINL
DYNAMIC CHARACTERISTICS
V+ = 5.5V, VIN = 0V or V+
Full
2.4
1.5
-
V
Full
-
1.4
0.8
V
Full
-1
-
1
µA
Turn-ON Time, tON
V+ = 4.5V, VNO or VNC = 3V, RL = 300Ω, CL = 35pF,
VIN = 0 to 3V, See Figure 1
25
-
Full
-
64
80
ns
-
90
ns
Turn-OFF Time, tOFF
V+ = 4.5V, VNO or VNC = 3V, RL = 300Ω, CL = 35pF,
VIN = 0 to 3V, See Figure 1
25
-
Full
-
29
40
ns
-
45
ns
Break-before-make Time Delay, tD
Charge Injection, Q
NO OFF Capacitance, COFF
NC OFF Capacitance, COFF
COM ON Capacitance, CCOM(ON)
OFF Isolation
Crosstalk, Note 11
V+ = 5.5V, VNO or VNC = 3V, RL = 300Ω, CL = 35pF,
VIN = 0 to 3V, See Figure 3
CL = 1.0nF, VG = 0V, RG = 0ΩSee Figure 2
f = 1MHz, VNO or VNC = VCOM = 0V, See Figure 7
f = 1MHz, VNO or VNC = VCOM = 0V, See Figure 7
f = 1MHz, VNO or VNC = VCOM = 0V, See Figure 7
RL = 50Ω, CL = 15pF, f = 1MHz,
VNO or VNC = 1VRMS, See Figures 4 and 6
Full
15
39
25
-
1.2
25
-
10
25
-
10
25
-
30
25
-
71
25
-
-92
-
ns
2
pC
-
pF
-
pF
-
pF
-
dB
-
dB
Power Supply Rejection Ratio
RL = 50Ω, CL = 5pF, f = 1MHz
25
-
59
-
dB
Submit Document Feedback
4
FN6036.3
December 15, 2014
 ▷