ISL43110_05 Datasheet, PDF (4/12 Pages) Intersil Corporation – Low-Voltage, Single Supply, SPST, High Performance Analog Switches

ISL43110, ISL43111
Electrical Specifications: 5V Supply
Test Conditions: V+ = +4.5V to +5.5V, GND = 0V, V_INH = 2.4V, V_INL = 0.8V (Note 4),
Unless Otherwise Specified (Continued)
PARAMETER
TEST CONDITIONS
TEMP (NOTE 5)
(NOTE 5)
(°C)
MIN
TYP
MAX UNITS
Power Supply Rejection Ratio
R_L = 50Ω, C_L = 5pF, f = 1MHz
25
-
60
-
dB
NO or NC OFF Capacitance, C_OFF f = 1MHz, V_NO or V_NC = V_COM = 0V, (See Figure 5)
25
-
15
-
pF
COM OFF Capacitance,
C_COM(OFF)
f = 1MHz, V_NO or V_NC = V_COM = 0V, (See Figure 5)
25
-
15
-
pF
COM ON Capacitance, C_COM(ON) f = 1MHz, V_NO or V_NC = V_COM = 0V, (See Figure 5)
25
-
40
-
pF
POWER SUPPLY CHARACTERISTICS
Positive Supply Current, I+
V+ = 5.5V, V_IN = 0V or V+, Switch On or Off
Full
-1
-
1
µA
NOTES:
4. V_IN = input voltage to perform proper function.
5. The algebraic convention, whereby the most negative value is a minimum and the most positive a maximum, is used in this data sheet.
6. Leakage parameter is 100% tested at high temp, and guaranteed by correlation at 25°C.
Electrical Specifications: 12V Supply
Test Conditions: V+ = +10.8V to +13V, GND = 0V, V_INH = 4V, V_INL = 0.8V (Note 4),
Unless Otherwise Specified
PARAMETER
TEST CONDITIONS
TEMP (NOTE 5)
(°C)
MIN
(NOTE 5)
TYP
MAX UNITS
ANALOG SWITCH CHARACTERISTICS
Analog Signal Range, V_ANALOG
ON Resistance, R_ON
V+ = 10.8V, I_COM = 1.0mA, V_COM = 10V
Full
0
25
-
Full
-
-
V+
V
7
10
Ω
8
15
Ω
R_ON Flatness, R_FLAT(ON)
I_COM = 1.0mA, V_COM = 3V, 6V, 9V
25
-
1
3
Ω
Full
-
1.5
5
Ω
NO or NC OFF Leakage Current, V+ = 13V, V_COM = 1V, 10V, V_NO or V_NC = 10V, 1V,
25
-1
-
1
nA
I_NO(OFF) or I_NC(OFF)
(Note 6)
Full
-10
-
10
nA
COM OFF Leakage Current,
V+ = 13V, V_COM = 10V, 1V, V_NO or V_NC = 1V, 10V,
25
-1
-
1
nA
I_COM(OFF)
(Note 6)
Full
-10
-
10
nA
COM ON Leakage Current,
I_COM(ON)
V+ = 13V, V_COM = 1V, 10V, or V_NO or V_NC = 1V, 10V, 25
-1
-
(Note 6)
Full
-20
-
1
nA
20
nA
DIGITAL INPUT CHARACTERISTICS
Input Voltage High, V_INH
Input Voltage Low, V_INL
Input Current, I_INH, I_INL
DYNAMIC CHARACTERISTICS
V+ = 13V, V_IN = 0V or V+
Full
4
Full
-
Full
-1
-
-
V
-
0.8
V
-
1
µA
Turn-ON Time, t_ON
V_NO or V_NC = 10V, R_L = 300Ω, C_L = 35pF
25
-
Full
-
37
80
ns
42
120
ns
Turn-OFF Time, t_OFF
V_NO or V_NC = 10V, R_L = 300Ω, C_L = 35pF
25
-
Full
-
21
50
ns
26
75
ns
Charge Injection, Q
C_L = 1.0nF, V_G = 0V, R_G = 0Ω
OFF Isolation
R_L = 50Ω, C_L = 15pF, f = 100kHz
Power Supply Rejection Ratio
R_L = 50Ω, C_L = 5pF, f = 1MHz
NO or NC OFF Capacitance, C_OFF f = 1MHz, V_NO or V_NC = V_COM = 0V
25
-
8
20
pC
25
-
>90
-
dB
25
-
67
-
dB
25
-
15
-
pF
4
FN6028.3
April 12, 2005