ISL43110_05 Datasheet, PDF (3/12 Pages) Intersil Corporation – Low-Voltage, Single Supply, SPST, High Performance Analog Switches

ISL43110, ISL43111
Absolute Maximum Ratings
V+ to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3 to15V
Input Voltages
IN (Note 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3 to ((V+) + 0.3V)
NO, NC (Note 2) . . . . . . . . . . . . . . . . . . . . . . . -0.3 to ((V+) + 0.3V)
Output Voltages
COM (Note 2). . . . . . . . . . . . . . . . . . . . . . . . . . -0.3 to ((V+) + 0.3V)
Continuous Current (Any Terminal) . . . . . . . . . . . . . . . . . . . . . 20mA
Peak Current NO, NC, or COM
(Pulsed 1ms, 10% Duty Cycle, Max) . . . . . . . . . . . . . . . . . . . . 30mA
ESD Rating (Per MIL-STD-883 Method 3015). . . . . . . . . . . . . >2kV
Thermal Information
Thermal Resistance (Typical, Note 3)
θ_JA (°C/W)
5 Ld SOT-23 Package . . . . . . . . . . . . . . . . . . . . . . .
225
8 Ld SOIC Package . . . . . . . . . . . . . . . . . . . . . . . . .
170
Maximum Junction Temperature (Plastic Package). . . . . . . . 150°C
Moisture Sensitivity (See Technical Brief TB363)
All Packages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Level 1
Maximum Storage Temperature Range . . . . . . . . . . . . . -65°C to 150°C
Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . 300°C
(Lead Tips Only)
Operating Conditions
Temperature Range
ISL4311XIX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -40°C to 85°C
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTES:
2. Signals on NO, NC, COM, or IN exceeding V+ or GND are clamped by internal diodes. Limit forward diode current to maximum current ratings.
3. θ_JA is measured with the component mounted on a low effective thermal conductivity test board in free air. See Tech Brief TB379 for details.
Electrical Specifications: 5V Supply
Test Conditions: V+ = +4.5V to +5.5V, GND = 0V, V_INH = 2.4V, V_INL = 0.8V (Note 4),
Unless Otherwise Specified
PARAMETER
TEST CONDITIONS
TEMP (NOTE 5)
(NOTE 5)
(°C)
MIN
TYP
MAX UNITS
ANALOG SWITCH CHARACTERISTICS
Analog Signal Range, V_ANALOG
ON Resistance, R_ON
V+ = 4.5V, I_COM = 1.0mA, V_COM = 3.5V,
(See Figure 4)
Full
0
25
-
Full
-
-
V+
V
11
20
Ω
15
25
Ω
R_ON Flatness, R_FLAT(ON)
I_COM = 1.0mA, V_COM = 1V, 2V, 3V
25
-
1.5
3
Ω
Full
-
2.5
5
Ω
NO or NC OFF Leakage Current, V+ = 5.5V, V_COM = 1V, 4.5V, V_NO or V_NC = 4.5V, 1V,
25
-1
I_NO(OFF) or I_NC(OFF)
(Note 6)
Full
-10
0.01
-
1
nA
10
nA
COM OFF Leakage Current,
I_COM(OFF)
V+ = 5.5V, V_COM = 4.5V, 1V, V_NO or V_NC = 1V, 4.5V,
25
-1
(Note 6)
Full
-10
0.01
-
1
nA
10
nA
COM ON Leakage Current,
I_COM(ON)
V+ = 5.5V, V_COM = 1V, 4.5V, or V_NO or V_NC = 1V, 4.5V, 25
-1
(Note 6)
Full
-20
0.01
-
1
nA
20
nA
DIGITAL INPUT CHARACTERISTICS
Input Voltage High, V_INH
Input Voltage Low, V_INL
Input Current, I_INH, I_INL
DYNAMIC CHARACTERISTICS
V+ = 5.5V, V_IN = 0V or V+
Full
2.4
-
-
V
Full
-
-
0.8
V
Full
-1
-
1
µA
Turn-ON Time, t_ON
V_NO or V_NC = 3V, R_L = 300Ω, C_L = 35pF,
V_IN = 0 to 3V, (See Figure 1)
25
-
Full
-
45
80
ns
50
120
ns
Turn-OFF Time, t_OFF
V_NO or V_NC = 3V, R_L = 300Ω, C_L = 35pF,
V_IN = 0 to 3V, (See Figure 1)
25
-
Full
-
20
50
ns
28
75
ns
Charge Injection, Q
OFF Isolation
C_L = 1.0nF, V_G = 0V, R_G = 0Ω, (See Figure 2)
R_L = 50Ω, C_L = 15pF, f = 100kHz, (See Figure 3)
25
-
2
10
pC
25
-
>90
-
dB
3
FN6028.3
April 12, 2005