ISL22317_10 Datasheet, PDF (4/15 Pages) Intersil Corporation – Precision Single Digitally Controlled Potentiometer (XDCP™)

ISL22317
Analog Specifications Over recommended operating conditions unless otherwise stated. (Continued)
SYMBOL
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
(Note 22) (Note 7) (Note 22) UNIT
ZSerror
(Note 9)
Zero-scale Error
FSerror Full-scale Error
(Note 10)
TC_V
Ratiometric Temperature Coefficient
(Notes 13, 19)
W, U or T option
V_RL < V_RW < V_RL + 0.3V
W, U or T option
V_CC - 0.3V < V_RW < V_CC
Match to external Rref, DCP register set
between 15 hex and 7F hex
0.5
2
LSB
(Note 8)
-2
-0.5
LSB
(Note 8)
TCref
±10
ppm/°C
f_cutoff
-3dB Cut Off Frequency
Wiper at midpoint (40hex) W option (10k)
1
kHz
(Note 19)
Wiper at midpoint (40hex) U option (50k)
1
kHz
Wiper at midpoint (40hex) T option (100k)
1
kHz
RESISTOR MODE (Measurements between RW and RL with RH not connected)
RINL
Integral Non-linearity
(Note 17)
RDNL
Differential Non-linearity
(Note 16)
Roffset Offset
(Note 15)
W, U or T option
Current forced to the wiper
I_W = (V_CC - V_RL)/R_TOTAL (Note 20)
W, U or T option
Current forced to the wiper
I_W = (V_CC - V_RL)/R_TOTAL (Note 20)
W, U or T option, wiper is out of
recommended operation conditions
-3
±1
3
MI
(Note 14)
-3
±1
3
MI
(Note 14)
0
1
2
MI
(Note 14)
TC_R
Resistance Temperature Coefficient Match to external Rref, DCP register set
(Notes 18, 19)
between 15 hex and 7F hex, all options
TCref
±10
ppm/°C
Operating Specifications Over the recommended operating conditions unless otherwise specified.
SYMBOL
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
(Note 22) (Note 7) (Note 22)
I_CC1
V_CC Supply Current (volatile
write/read)
(Vfo^Cr^CI^{2=C+, 5a.c5tViv,ef,S}r^Ce^Lad=
400kHz; SDA = Open;
and write states)
0.6
1.2
(Vfo^Cr^CI^{2=C+, 2a.c7tViv,ef,S}r^Ce^Lad=
400kHz; SDA = Open;
and write states), 10k
0.35
0.9
I_CC2
V_CC Supply Current (non-volatile
write/read)
(Vfo^Cr^CI^{2=C+, 5a.c5tViv,ef,S}r^Ce^Lad=
400kHz; SDA = Open;
and write states)
1.75
2.5
I_SB
V_CC Current (Standby)
I_SD
V_CC Current (Shutdown)
(Vfo^Cr^CI^{2=C+, 2a.c7tViv,ef,S}r^Ce^Lad=
400kHz; SDA = Open;
and write states)
V_CC = +5.5V @ +125°C, I²C interface in
standby state
V_CC = +2.7V @ +125°C, I²C interface in
standby state, 10k
V_CC = +5.5V @ +125°C, I²C interface in
standby state
1.0
1.8
0.5
1.0
0.3
0.75
0.5
1.5
I_LkgDig Leakage Current, at Pins REF_A,
Voltage at pin from GND to V_CC
-0.25
0.25
REF_B, A1, SDA, and SCL
t_DCP
DCP Wiper Response Time
SCL falling edge of last bit of DCP data byte
150
(Note 19)
to wiper new position
t_ShdnRec DCP Recall Time from Shutdown
SCL falling edge of last bit of ACR data byte
150
(Note 19) Mode
to wiper stored position and RH connection
Vpor Power-on Recall Voltage
Minimum V_CC at which memory recall occurs
2.6
VCC Ramp V_CC Ramp Rate
0.2
50
UNIT
mA
mA
mA
mA
mA
mA
µA
µA
µs
µs
V
V/ms
4
FN6912.1
April 15, 2010