HFA3663 Datasheet, PDF (4/5 Pages) Intersil Corporation – 2.3GHz UpConverter with Gain Control

HFA3663
Electrical Specifications
V_CC = 5.5V, LO = 2050MHz, IF = 100MHz, RF = 2150MHz, Z_O = 50Ω,
Unless Otherwise Specified (Continued)
PARAMETER
(NOTE 2)
TEST
TEMP
SYMBOL
LEVEL
(^oC)
MIN
TYP
MAX UNITS
TRANSMIT POWER PREAMP CHARACTERISTICS (PRE_IN = 2150MHz/-30dBm, AGC_CTRL = 0.7V (Max Gain))
Frequency Range
PRE_f
B
25
2.0
-
2.3
GHz
Power Gain
(AGC_CTRL = 0.7V)
V_CC = 5.5V
PRE_PGH
A
25, 85
18
24
-
dB
Pre-Amp Noise Figure (Max Gain)
PRE_NF
B
25
-
8
-
dB
Pre-Amp AGC Range (Max - Min Gain)
PRE_AGC
A
25
20
30
-
dB
AGC Control Voltage Range
AGC_V
A
25
0.7
-
1.7
V
AGC Control Linearity
AGC_LIN
B
25
-
5:1
-
-
AGC Settling Time (Min to Max Gain)
AGC_T1
B
25
-
8.0
-
µS
AGC Settling Time (Max to Min Gain)
AGC_T2
B
25
-
0.1
-
µS
Pre-Amp RF Output 1dB
Compression
V_CC = 5.5V
PRE_P1DH
A
25
8
10
-
dBm
RF Output Third Order Intercept
PRE_IP3
C
25
-
17
-
dBm
Input VSWR
PRE_ISWR
A
25, 85
-
2.7:1
3.0:1
-
Input Return Loss
PRE_IRL
A
25, 85
6.02
9.0
-
dB
Output VSWR
PRE_OSWR
A
25, 85
1.0
1.17:1
2.0:1
-
Output Return Loss
PRE_ORL
A
25, 85
9.4
15.4
-
dB
POWER SUPPLY AND LOGIC CHARACTERISTICS
Voltage Supply Range
V_CC
A
25
4.5
-
5.5
V
Supply Current (V_CC = 5.5V)
I_{CC HI}
A
25, 85
9.0
100
110
mA
I_{CC HI}T
C
Full
-
-
110
mA
Power Down Supply Current (V_CC = 5.5V)
I_CC_PD
A
25
0.004
2.8
4
mA
Logic Input Low Level
V_IL
A
25
-0.2
-
0.8
V
Logic Input High Level
V_IH
A
25
2.0
-
V_CC
V
Logic Low Input Bias Current
(V_PE = 0V, V_CC = 5.5V)
I_B_LO
A
25
-
-5.0
5.0
µA
Logic High Input Bias Current
(V_PE = 5.5V, V_CC = 5.5V)
I_B_HI
A
25
-
-5.0
5.0
µA
Vagc High Input Bias Current
(Vagc = 2.1V, V_CC = 5.5V)
Ivagc_HI
A
25
-
10
400
µA
Vagc Low Input Bias Current
(Vagc = 0.7V, V_CC = 5.5V)
Ivagc_LO
A
25
-400
-10
-
µA
Power Enable Time (50% V_PE to 90% I_CC)
PEt
B
25
-
5
10
µs
Power Disable Time (50% V_PE to 10% I_CC)
PDt
B
25
-
0.1
10
µs
NOTES:
2. Test Level: A = 100% production tested, B = Typical or Limit based on characterization data, C = Design information, goal or condition.
3. Bias Resistor at pin 16 changes according to the relationship mentioned in Note 4 of the Typical Applications Circuit.
2-204