HFA3663 Datasheet, PDF (3/5 Pages) Intersil Corporation – 2.3GHz UpConverter with Gain Control

HFA3663
Absolute Maximum Ratings
Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3 to 6.0V
Voltage on Any Other Pin. . . . . . . . . . . . . . . . . . . . -0.3 to V_CC 0.3V
Operating Conditions
Supply Voltage Range . . . . . . . . . . . . . . . . . . . . . . . . . . 2.7V to 5.5V
Thermal Information
Thermal Resistance (Typical, Note 1)
θ_JA (^oC/W)
20 Lead SSOP . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
110
Package Power Dissipation at 70^oC
20 Lead SSOP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0.7W
Maximum Junction Temperature (Plastic Package) . . . . . . . . .150^oC
Maximum
Maximum
Temperature Range. . . . . . .
Storage Temperature Range
.
.
.
.
.
.
.
.
.
.
.
.
.
.
-.6-45^o0CoC≤≤T_A^TA≤≤15805^ooCC
Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . 300^oC
(Lead Tips Only)
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTE:
1. θ_JA is measured with the component mounted on an evaluation PC board in free air.
Electrical Specifications
V_CC = 5.5V, LO = 2050MHz, IF = 100MHz, RF = 2150MHz, Z_O = 50Ω,
Unless Otherwise Specified
PARAMETER
(NOTE 2)
TEST
TEMP
SYMBOL
LEVEL
(^oC)
MIN
TYP
MAX
CASCADED CHARACTERISTICS (-3dB Loss RF Image Filter with 35dB LO Suppression,
LO_IN = 2050MHz/-6dBm, IF_IN = 100MHz/-30dBm, AGC_CTRL = 0.7V (Max Gain))
Cascaded Output 1dB Compression
CTX_P1D
B
25
6
7.5
-
Cascaded Output Third Order Intercept
CTX_IP3
C
25
-
14
-
Cascaded Power Gain
CTX_PG
B
25
18
22
-
Cascaded Power Gain Flatness
(2.0GHz to 2.3GHz)
CTX_PGF
C
25
-2.5
0
+2.5
Cascaded LO Leakage
CTX_LEAK
B
25
-
-20
-
LO INPUT CHARACTERISTICS (LO_IN = 2050MHz/-6dBm, all unused inputs and outputs are terminated into 50Ω)
LO Input Frequency Range
LO_f
B
25
1.6
-
2.29
LO Input Drive Level
LO_dr
A
25
-
-6
-
LO Input VSWR
LO_SWR
A
25, 85
-
1.62:1
2.0:1
LO Input Return Loss
LO_IRL
A
25, 85
9.4
12.5
-
TRANSMIT MIXER CHARACTERISTICS (LO_IN = 2050MHz/-6dBm, TXM_IF = 100MHz/-30dBm)
IF Input Frequency Range
TXM_IFf
B
25
10
-
400
IF Input VSWR
TXM_SWR
A
25, 85
-
1.22:1
2.0:1
IF Input Return Loss
TXM_IRL
A
25, 85
9.4
23
-
Power Conversion Gain
(Note 3)
V_CC = 5.5V
TXM_PGH
A
25, 85
3.0
5.6
TBD
Transmit Mixer LO Leakage
TXM_LEAK
A
25, 85
-
-20
-10
RF Output Frequency Range
TXM_RFf
B
25
2.0
-
2.3
RF Output VSWR
TXM_OSWR
A
25, 85
-
1.68:1
2.0:1
RF Output Return Loss
TXM_ORL
A
25, 85
9.4
17.4
-
RF Output 1dB Compression
(Note 3)
V_CC = 5.5V
TXM_P1DH
A
25
-7.8
-6.5
-
RF Output Third Order Intercept
TXM_IP3
C
25
-
2.7
-
Transmit Mixer Noise Figure
TXM_NF
B
25
-
18
-
UNITS
dBm
dBm
dB
dB
dBm
GHz
dBm
-
dB
MHz
-
dB
dB
dBm
GHz
-
dB
dBm
dBm
dB
2-203