HA5022_03 Datasheet, PDF (4/17 Pages) Intersil Corporation – Dual, 125MHz, Video Current Feedback Amplifier with Disable

HA5022
Electrical Specifications
PARAMETER
V_SUPPLY = ±5V, R_F = 1kΩ, A_V = +1, R_L = 400Ω, C_L ≤ 10pF, Unless Otherwise Specified (Continued)
TEST
CONDITIONS
(NOTE 11)
TEST
TEMP.
LEVEL
(^oC)
MIN
TYP
MAX
UNITS
AC CHARACTERISTICS (A_V = +2, R_F = 681Ω)
Slew Rate
Note 8
B
25
-
475
-
V/µs
Full Power Bandwidth
Note 9
B
25
-
26
-
MHz
Rise Time
Note 10
B
25
-
6
-
ns
Fall Time
Note 10
B
25
-
6
-
ns
Propagation Delay
Note 10
B
25
-
6
-
ns
Overshoot
B
25
-
12
-
%
-3dB Bandwidth
Settling Time to 1%
V_OUT = 100mV
2V Output Step
B
25
-
95
-
MHz
B
25
-
50
-
ns
Settling Time to 0.25%
2V Output Step
B
25
-
100
-
ns
Gain Flatness
5MHz
B
25
-
0.02
-
dB
20MHz
B
25
-
0.07
-
dB
AC CHARACTERISTICS (A_V = +10, R_F = 383Ω)
Slew Rate
Note 8
B
25
350
475
-
V/µs
Full Power Bandwidth
Note 9
B
25
28
38
-
MHz
Rise Time
Note 10
B
25
-
8
-
ns
Fall Time
Note 10
B
25
-
9
-
ns
Propagation Delay
Note 10
B
25
-
9
-
ns
Overshoot
B
25
-
1.8
-
%
-3dB Bandwidth
Settling Time to 1%
V_OUT = 100mV
2V Output Step
B
25
-
65
-
MHz
B
25
-
75
-
ns
Settling Time to 0.1%
2V Output Step
B
25
-
130
-
ns
VIDEO CHARACTERISTICS
Differential Gain (Note 15)
R_L = 150Ω
B
25
-
0.03
-
%
Differential Phase (Note 15)
R_L = 150Ω
B
25
-
0.03
-
Degrees
NOTES:
5. V_CM = ±2.5V. At -40^oC Product is tested at V_CM = ±2.25V because short test duration does not allow self heating.
6. R_L = 100Ω, V_IN = 2.5V. This is the minimum current which must be pulled out of the Disable pin in order to disable the output. The output is
considered disabled when -10mV ≤ V_OUT ≤ +10mV.
7. V_IN = 0V. This is the maximum current that can be pulled out of the Disable pin with the HA5022 remaining enabled. The HA5022 is
considered disabled when the supply current has decreased by at least 0.5mA.
8. V_OUT switches from -2V to +2V, or from +2V to -2V. Specification is from the 25% to 75% points.
9. _{FPBW = 2}-^S---_π-^l--^e-_V--^w--_P----^R-_E---^a-_A---^t-^eK--- _{; VPEAK = 2V.}
10. R_L = 100Ω, V_OUT = 1V. Measured from 10% to 90% points for rise/fall times; from 50% points of input and output for propagation delay.
11. A. Production Tested; B. Typical or Guaranteed Limit based on characterization; C. Design Typical for information only.
12. V_IN = +2V, DISABLE = +5V to 0V. Measured from the 50% point of DISABLE to V_OUT = 0V.
13. V_IN = +2V, DISABLE = 0V to +5V. Measured from the 50% point of DISABLE to V_OUT = 2V.
14. V_IN = 0V, Force V_OUT from 0V to ±2.5V, t_R = t_F = 50ns, DISABLE = 0V.
15. Measured with a VM700A video tester using an NTC-7 composite VITS.
16. V_OUT = ±2.5V. At -40^oC Product is tested at V_OUT = ±2.25V because short test duration does not allow self heating.
4