DG508A Datasheet, PDF (4/9 Pages) Maxim Integrated Products – Monolithic CMOS Analog Multiplexers

DG508A
Electrical Specifications T_A = 25^oC, V+ = +15V, V- = -15V, GND = 0V, V_EN = 2.4V, Unless Otherwise Specified (Continued)
“A” SUFFIX
“B” AND “C” SUFFIX
PARAMETER
TEST CONDITIONS
(NOTE 4) (NOTE 3) (NOTE 4) (NOTE 4) (NOTE 3) (NOTE 4)
MIN
TYP
MAX
MIN
TYP
MAX UNITS
Source OFF Leakage
Current, I_S(OFF)
V_EN = 0V
Drain OFF Leakage
Current, I_D(OFF)
V_EN = 0V
Drain ON Leakage Current, (Note 6)
I_D(ON)
Sequence Each
Switch ON
V_AL = 0.8V,
V_AH = 2.4V
POWER SUPPLY CHARACTERISTICS
V_S = +10V, V_D = -10V
V_S = -10V, V_D = +10V
V_S = -10V, V_D = +10V
V_S = +10V, V_D = -10V
V_D = V_S(ALL) = +10V
V_D = V_S(ALL) = -10V
-1
0.002
1
-1
-0.005
1
-
0.01
10
-10
-0.015
-
-
0.015
10
-10
-0.03
-
-5
0.002
5
nA
-5
-0.005
5
nA
-
0.01
20
nA
-20 -0.015
-
nA
-
0.015
20
nA
-20
-0.03
-
nA
Positive Supply Current, I+ V_EN = 5.0V (Enabled) or
Negative Supply Current, I- ^{VEN = 0V (Standby), VA = 0V}
-
1.3
2.4
-
1.3
2.4
mA
-1.5
-0.7
-
-1.5
-0.7
-
mA
Electrical Specifications T_A = Over Operating Temperature Range, V+ = +15V, V- = -15V, GND = 0V, V_EN = 2.4V,
Unless Otherwise Specified
PARAMETER
TEST CONDITIONS
“A” SUFFIX
(NOTE 3)
MIN TYP MAX
UNITS
DIGITAL INPUT CHARACTERISTICS
Address Input Current, Input Voltage
High, I_AH
V_A = 2.4V
V_A = 15V
Address Input Current Input Voltage
Low, I_AL
V_EN = 2.4V
V_EN = 0V
ANALOG SWITCH CHARACTERISTICS
V_A = 0V
-30
-
-
µA
-
-
30
µA
-30
-
-
µA
-30
-
-
µA
Analog Signal Range, V_ANALOG
(Note 7)
-15
-
+15
V
Drain-Source ON Resistance, r_DS(ON) Sequence Each Switch ON
V_AL = 0.8V, V_AH = 2.4V
I_S = -200µA, V_D = +10V
-
I_S = -200µA, V_D = -10V
-
-
500
Ω
-
500
Ω
Source OFF Leakage Current, I_S(OFF) V_EN = 0V
V_S = +10V, V_D = -10V
-
-
50
nA
V_S = -10V, V_D = +10V
-50
-
-
nA
Drain OFF Leakage Current, I_D(OFF) V_EN = 0V
V_S = -10V, V_D = +10V
-
-
200
nA
V_S = +10V, V_D = -10V
-200
-
-
nA
Drain ON Leakage Current, I_D(ON)
(Note 6) Sequence Each Switch ON V_D = V_S(ALL) = +10V
V_AL = 0.8V, V_AH = 2.4V
V_D = V_S(ALL) = -10V
-
-
-200
-
200
nA
-
nA
POWER SUPPLY CHARACTERISTICS
Positive Supply Current, I+
Negative Supply Current, I-
V_EN = 5.0V, V_A = 0V
-3.2
-
4.5
mA
-3.2
-
4.5
mA
Positive Standby Supply Current, I+
Negative Standby Supply Current, I-
V_EN = 0V, V_A = 0V
-3.2
-
4.5
mA
-3.2
-
4.5
mA
NOTES:
3. Typical values are for design aid only, not guaranteed and not subject to production testing.
4. The algebraic convention whereby the most negative value is a minimum, and the most positive value is a maximum, is used in this data sheet.
5. Off isolation = 20Log |V_S|/|V_D|, where V_S = input to Off switch, and V_D = output due to V_S.
6. I_D(ON) is leakage from driver into “ON” switch.
7. Parameter not tested. Parameter guaranteed by design or characterization.
4