DG411_06 Datasheet, PDF (4/13 Pages) Intersil Corporation – Monolithic Quad SPST, CMOS Analog Switches

DG411, DG412, DG413
Absolute Maximum Ratings
V+ to V- . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44V
GND to V-. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25V
V_L. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (GND -0.3V) to (V+) +0.3V
Digital Inputs, V_S, V_D (Note 1). . . . . (V-) -2V to (V+) + 2V or 30mA,
Whichever Occurs First
Continuous Current (Any Terminal) . . . . . . . . . . . . . . . . . . . . . 30mA
Peak Current, S or D (Pulsed 1ms, 10% Duty Cycle Max) . . 100mA
Operating Conditions
Voltage Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±20V (Max)
Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . .-40°C to +85°C
Input Low Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.8V (Max)
Input High Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.4V (Min)
Input Rise and Fall Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . ≤20ns
Thermal Information
Thermal Resistance (Typical, Note 2)
θ_JA (°C/W)
PDIP Package* . . . . . . . . . . . . . . . . . . . . . . . . . . . .
90
SOIC Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
110
TSSOP Package . . . . . . . . . . . . . . . . . . . . . . . . . . .
150
Maximum Junction Temperature (Plastic Packages). . . . . . . +150°C
Maximum Storage Temperature Range . . . . . . . . . .-65°C to +150°C
Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . +300°C
(SOIC and TSSOP - Lead Tips Only)
*Pb-free PDIPs can be used for through hole wave solder
processing only. They are not intended for use in Reflow solder
processing applications.
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTES:
1. Signals on S_X, D_X, or IN_X exceeding V+ or V- will be clamped by internal diodes. Limit forward diode current to maximum current ratings.
2. θ_JA is measured with the component mounted on a low effective thermal conductivity test board in free air. See Tech Brief TB379 for details.
Electrical Specifications Test Conditions: V+ = +15V, V- = -15V, V_L = 5V, V_IN = 2.4V, 0.8V (Note 3),
Unless Otherwise Specified
PARAMETER
TEST CONDITIONS
TEMP (NOTE 4) (NOTE 5) (NOTE 4)
(°C)
MIN
TYP
MAX UNITS
DYNAMIC CHARACTERISTICS
Turn-ON Time, t_ON
R_L = 300Ω, C_L = 35pF, V_S = ±10V (Figure 1)
25
-
110
175
ns
85
-
-
220
ns
Turn-OFF Time, t_OFF
25
-
100
145
ns
85
-
-
160
ns
Break-Before-Make Time Delay
DG413 Only, R_L = 300Ω, C_L = 35pF (Figure 2)
25
-
25
-
ns
Charge Injection, Q (Figure 3)
C_L = 10nF, V_G = 0V, R_G = 0Ω
25
-
5
-
pC
OFF Isolation (Figure 5)
R_L = 50Ω, C_L = 5pF, f = 1MHz
25
-
68
-
dB
Crosstalk (Channel-to-Channel),
(Figure 4)
25
-
-85
-
dB
Source OFF Capacitance, C_S(OFF) f = 1MHz (Figure 6)
Drain OFF Capacitance, C_D(OFF)
Channel ON Capacitance,
C_D(ON) + C_S(ON)
DIGITAL INPUT CHARACTERISTICS
25
-
9
-
pF
25
-
9
-
pF
25
-
35
-
pF
Input Current V_IN Low, I_IL
V_IN Under Test = 0.8V, All Others = 2.4V
Input Current V_IN High, I_IH
V_IN Under Test = 2.4V, All Others = 0.8V
ANALOG SWITCH CHARACTERISTICS
Full
-0.5
0.005
0.5
μA
Full
-0.5
0.005
0.5
μA
Analog Signal Range, V_ANALOG
I_S = 10mA
Full
-15
-
15
V
Drain-Source ON Resistance,
I_S = 10mA, V_D = ±8.5V, V+ = 13.5V, V- = -13.5V
25
-
r_DS(ON)
Full
-
25
35
Ω
-
45
Ω
4
FN3282.12
November 27, 2006