English
Language : 

DG411DVZ-T Datasheet, PDF (4/13 Pages) Intersil Corporation – Monolithic Quad SPST, CMOS Analog Switches
◁
DG411, DG412, DG413
Absolute Maximum Ratings
V+ to V- . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44V
GND to V-. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25V
VL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (GND -0.3V) to (V+) +0.3V
Digital Inputs, VS, VD (Note 1). . . . . (V-) -2V to (V+) + 2V or 30mA,
Whichever Occurs First
Continuous Current (Any Terminal) . . . . . . . . . . . . . . . . . . . . . 30mA
Peak Current, S or D (Pulsed 1ms, 10% Duty Cycle Max) . . 100mA
Operating Conditions
Voltage Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±20V (Max)
Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . .-40°C to +85°C
Input Low Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.8V (Max)
Input High Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.4V (Min)
Input Rise and Fall Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . ≤20ns
Thermal Information
Thermal Resistance (Typical, Note 2)
θJA (°C/W)
PDIP Package* . . . . . . . . . . . . . . . . . . . . . . . . . . . .
90
SOIC Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
110
TSSOP Package . . . . . . . . . . . . . . . . . . . . . . . . . . .
150
Maximum Junction Temperature (Plastic Packages). . . . . . . +150°C
Maximum Storage Temperature Range . . . . . . . . . .-65°C to +150°C
Pb-free reflow profile . . . . . . . . . . . . . . . . . . . . . . . . . .see link below
http://www.intersil.com/pbfree/Pb-FreeReflow.asp
(SOIC and TSSOP - Lead Tips Only)
*Pb-free PDIPs can be used for through hole wave solder
processing only. They are not intended for use in Reflow solder
processing applications.
CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product reliability and
result in failures not covered by warranty.
NOTES:
1. Signals on SX, DX, or INX exceeding V+ or V- will be clamped by internal diodes. Limit forward diode current to maximum current ratings.
2. θJA is measured with the component mounted on a low effective thermal conductivity test board in free air. See Tech Brief TB379 for details.
Electrical Specifications Test Conditions: V+ = +15V, V- = -15V, VL = 5V, VIN = 2.4V, 0.8V (Note 3),
Unless Otherwise Specified.
PARAMETER
TEST CONDITIONS
TEMP
MIN
(°C) (Note 4)
DYNAMIC CHARACTERISTICS
Turn-ON Time, tON
RL = 300Ω, CL = 35pF, VS = ±10V (Figure 1)
25
-
85
-
Turn-OFF Time, tOFF
25
-
85
-
Break-Before-Make Time Delay
DG413 Only, RL = 300Ω, CL = 35pF (Figure 2)
25
-
Charge Injection, Q (Figure 3)
CL = 10nF, VG = 0V, RG = 0Ω
25
-
OFF Isolation (Figure 5)
RL = 50Ω, CL = 5pF, f = 1MHz
25
-
Crosstalk (Channel-to-Channel),
(Figure 4)
25
-
Source OFF Capacitance, CS(OFF) f = 1MHz (Figure 6)
Drain OFF Capacitance, CD(OFF)
Channel ON Capacitance,
CD(ON) + CS(ON)
DIGITAL INPUT CHARACTERISTICS
25
-
25
-
25
-
Input Current VIN Low, IIL
VIN Under Test = 0.8V, All Others = 2.4V
Input Current VIN High, IIH
VIN Under Test = 2.4V, All Others = 0.8V
ANALOG SWITCH CHARACTERISTICS
Full
-0.5
Full
-0.5
Analog Signal Range, VANALOG
IS = 10mA
Full
-15
Drain-Source ON Resistance,
IS = 10mA, VD = ±8.5V, V+ = 13.5V, V- = -13.5V
25
-
rDS(ON)
Full
-
TYP
(Note 5)
110
-
100
-
25
5
68
-85
9
9
35
0.005
0.005
-
25
-
MAX
(Note 4) UNITS
175
ns
220
ns
145
ns
160
ns
-
ns
-
pC
-
dB
-
dB
-
pF
-
pF
-
pF
0.5
μA
0.5
μA
15
V
35
Ω
45
Ω
4
FN3282.13
June 20, 2007
 ▷