ISL59482_14 Datasheet, PDF (3/15 Pages) Intersil Corporation – Dual, 500MHz Triple, Multiplexing Amplifiers

ISL59482
Pin Description
ISL59482
(48 LD QFN) PIN NAME
1
OUTC1
2
OUTB1
3, 23
V1-, V2-
4
OUTA1
5, 25
V1+, V2+
6
EN1
26
EN2
7
27
8
9
10
11
12
13
14
15
16
17
18
19, 47
20, 48
21
22
24
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
HIZ1
HIZ2
IN0C1
IN0B1
IN0A1
GND
IN1A1
IN2B2
IN2C2
GND
IN3A2
IN3B2
IN3C2
S1-2, S1-1
S0-2, S0-1
OUTC2
OUTB2
OUTA2
IN0C2
IN0B2
IN0A2
GND
IN1A2
IN1B2
IN1C2
GND
IN2A2
IN1B1
IN1C1
GND
IN2A1
IN2B1
IN2C1
GND
IN3A1
IN3B1
IN3C1
EQUIVALENT
CIRCUIT
DESCRIPTION
Circuit 3 Output of amplifier C1
Circuit 3 Output of amplifier B1
Circuit 4A Negative power supply #1 and #2
Circuit 3 Output of amplifier A1
Circuit 4A Positive Power Supply #1 and #2
Circuit 2
Device enable (active low) w/internal pull-down resistor. A logic High puts device into power-down mode
leaving the logic circuitry active. This state is not recommended for logic control where more than one
MUX-amp share the same video output line.
Circuit 2 Output disable (active high) w/internal pull-down resistor. A logic high puts the output in a high impedance
state. Use this state when more than one MUX-amp share the same video output line.
Circuit 1
Circuit 1
Circuit 1
Circuit 4A
Circuit 1
Circuit 1
Circuit 1
Circuit 4B
Circuit 1
Circuit 1
Circuit 1
Circuit 2
Circuit 2
Circuit 2
Circuit 1
Circuit 1
Circuit 1
Circuit 1
Circuit 1
Circuit 4B
Circuit 1
Circuit 1
Circuit 1
Circuit 4B
Circuit 1
Circuit 1
Circuit 1
Circuit 4A
Circuit 1
Circuit 1
Circuit 1
Circuit 4A
Circuit 1
Circuit 1
Circuit 1
Channel 0 input for amplifier C1
Channel 0 input for amplifier B1
Channel 0 input for amplifier A1
Ground pin for amplifier A1
Channel 1 input for amplifier A1
Channel 2 input for amplifier B2
Channel 2 input for amplifier C2
Ground pin for amplifier C2
Channel 3 input for amplifier A2
Channel 3 input for amplifier B2
Channel 3 input for amplifier C2
Channel select pin MSB (binary logic code) for amplifiers A2, B2, C2 (S1-2) and A1, B1, C1 (S1-1)
Channel select pin LSB (binary logic code) for amplifiers A2, B2, C2 (S0-2) and A1, B1, C1 (S0-1)
Output of amplifier C2
Output of amplifier B2
Output of amplifier A2
Channel 0 input for amplifier A2
Channel 0 input for amplifier B2
Channel 0 input for amplifier C2
Ground pin for amplifier A2
Channel 1 input for amplifier A2
Channel 1 input for amplifier B2
Channel 1 input for amplifier C2
Ground pin for amplifier B2
Channel 2 input for amplifier A2
Channel 1 input for amplifier B1
Channel 1 input for amplifier C1
Ground pin for amplifier B1
Channel 2 input for amplifier A1
Channel 2 input for amplifier B1
Channel 2 input for amplifier C1
Ground pin for amplifier C1
Channel 3 input for amplifier A1
Channel 3 input for amplifier B1
Channel 3 input for amplifier C1
Submit Document Feedback
3
FN6209.4
August 8, 2014