English
Language : 

ISL54056_07 Datasheet, PDF (3/12 Pages) Intersil Corporation – Ultra Low ON-Resistance, +1.65V to +4.5V, Single Supply, Quad SPDT (Dual DPDT) Analog Switch
◁
ISL54056
Absolute Maximum Ratings
V+ to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.5 to 5.5V
Input Voltages
NO, NC, IN (Note 2) . . . . . . . . . . . . . . . . . . . -0.5 to ((V+) + 0.5V)
Output Voltages
COM (Note 2) . . . . . . . . . . . . . . . . . . . . . . . . -0.5 to ((V+) + 0.5V)
Continuous Current NO, NC, or COM . . . . . . . . . . . . . . . . . ±300mA
Peak Current NO, NC, or COM
(Pulsed 1ms, 10% Duty Cycle, Max) . . . . . . . . . . . . . . . . ±500mA
ESD Rating
Human Body Model (COMX) . . . . . . . . . . . . . . . . . . . . . . . . .>9kV
Human Body Model (NOX, NCX, INX, V+, GND) . . . . . . . . . .>6kV
Machine Model (COMX) . . . . . . . . . . . . . . . . . . . . . . . . . . . .>700V
Machine Model (NOX, NCX, INX, V+, GND) . . . . . . . . . . . . .>300V
Charged Device Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .>1kV
Thermal Information
Thermal Resistance (Typical)
θJA (°C/W)
μTQFN Package (Note 3) . . . . . . . . . . . . . . . . . . . .
93
Maximum Junction Temperature (Plastic Package). . . . . . . +150°C
Maximum Storage Temperature Range . . . . . . . . . . . -65°C to +150°C
Pb-free reflow profile . . . . . . . . . . . . . . . . . . . . . . . . . .see link below
http://www.intersil.com/pbfree/Pb-FreeReflow.asp
Operating Conditions
Temperature Range
ISL54056IRUZ . . . . . . . . . . . . . . . . . . . . . . . . . . . -40°C to +85°C
CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product reliability and
result in failures not covered by warranty.
NOTES:
2. Signals on NC, NO, IN, or COM exceeding V+ or GND are clamped by internal diodes. Limit forward diode current to maximum current ratings.
3. θJA is measured with the component mounted on a high effective thermal conductivity test board in free air. See Tech Brief TB379 for details.
Electrical Specifications - 4.3V Supply
Test Conditions: V+ = +3.9V to +4.5V, GND = 0V, VINH = 1.6V, VINL = 0.5V (Note 4),
Unless Otherwise Specified.
PARAMETER
TEST CONDITIONS
TEMP
MIN
MAX
(°C) (Notes 5, 8) TYP (Notes 5, 8) UNITS
ANALOG SWITCH CHARACTERISTICS
Analog Signal Range, VANALOG
Full
0
V+
V
ON-Resistance, rON
V+ = 3.9V, ICOM = 100mA, VNO or VNC = 0V to V+ 25
(See Figure 5)
Full
0.4
0.55
Ω
0.45
0.65
Ω
rON Matching Between Channels, V+ = 3.9V, ICOM = 100mA, VNO or VNC = Voltage at 25
ΔrON
max rON (Note 7)
Full
0.05
0.12
Ω
0.06
0.15
Ω
rON Flatness, rFLAT(ON)
V+ = 3.9V, ICOM = 100mA, VNO or VNC = 0V to V+ 25
(Note 6)
Full
0.05
0.15
Ω
0.05
0.15
Ω
NO or NC OFF Leakage Current, V+ = 4.5V, VCOM = 0.3V, 3V, VNO or VNC = 3V, 0.3V 25
INO(OFF) or INC(OFF)
Full
-70
-165
70
nA
165
nA
COM ON Leakage Current,
ICOM(ON)
V+ = 4.5V, VCOM = 0.3V, 3V, or VNO or VNC = 0.3V, 25
3V
Full
-70
-165
70
nA
165
nA
DYNAMIC CHARACTERISTICS
Turn-ON Time, tON
V+ = 3.9V, VNO or VNC = 3.0V, RL = 50Ω,
25
33
ns
CL = 35pF (See Figure 1)
Full
38
ns
Turn-OFF Time, tOFF
V+ = 3.9V, VNO or VNC = 3.0V, RL = 50Ω,
25
16
ns
CL = 35pF (See Figure 1)
Full
21
ns
Break-Before-Make Time Delay, tD V+ = 4.5V, VNO or VNC = 3.0V, RL = 50Ω, CL =
Full
3
ns
35pF (See Figure 3)
Charge Injection, Q
CL = 1.0nF, VG = 0V, RG = 0Ω (See Figure 2)
25
248
pC
OFF Isolation
RL = 50Ω, CL = 5pF, f = 100kHz, VCOM = 1VRMS
25
65
dB
(See Figure 4)
Crosstalk (Channel-to-Channel) RL = 50Ω, CL = 5pF, f = 100kHz, VCOM = 1VRMS
25
-85
dB
(See Figure 6)
Total Harmonic Distortion
f = 20Hz to 20kHz, VCOM = 2VP-P, RL = 600Ω
25
0.008
%
3
FN6357.4
August 15, 2007
 ▷