ISL43681_06 Datasheet, PDF (3/17 Pages) Intersil Corporation – Low-Voltage, Single and Dual Supply, 8 to 1 Multiplexer and Differential 4 to 1 Multiplexer

ISL43681, ISL43741
Absolute Maximum Ratings
V+ to V- . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3 to15V
V+ to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3 to15V
V- to GND. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -15 to 0.3V
Input Voltages
LE, EN, EN , NO, NC, ADD (Note 1) . . . . . . -0.3 to ((V+) + 0.3V)
Output Voltages
COM (Note 1) . . . . . . . . . . . . . . . . . . . . . . . . -0.3 to ((V+) + 0.3V)
Continuous Current (Any Terminal) . . . . . . . . . . . . . . . . . . . . ±30mA
Peak Current NO, NC, or COM
(Pulsed 1ms, 10% Duty Cycle, Max) . . . . . . . . . . . . . . . . ±100mA
ESD Rating
HBM ( Per Mil-STD-883, Method 3015.7) . . . . . . . . . . . . . >2.5kV
Thermal Information
Thermal Resistance (Typical, Note 2)
θ_JA (°C/W)
20 Ld 4x4 QFN Package . . . . . . . . . . . . . . . . . . . . .
45
Maximum Junction Temperature (Plastic Package). . . . . . . . 150°C
Maximum Storage Temperature Range . . . . . . . . . . . . . -65°C to 150°C
Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . 300°C
(Lead Tips Only)
Operating Conditions
Temperature Range
ISL43681IR and ISl43741IR . . . . . . . . . . . . . . . . . . . -40°C to 85°C
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTES:
1. Signals on NC, NO, COM, ADD, EN, EN, or LE exceeding V+ or V- are clamped by internal diodes. Limit forward diode current to maximum
current ratings.
2. θ_JA is measured with the component mounted on a high effective thermal conductivity test board with direct die attach. See Tech Brief TB379
for details.
Electrical Specifications ±5V Supply Test Conditions: V_SUPPLY = ±4.5V to ±5.5V, GND = 0V, V_INH = 2.4V, V_INL = 0.8V (Note 3),
Unless Otherwise Specified
PARAMETER
TEST CONDITIONS
TEMP (NOTE 4)
(NOTE 4)
(°C)
MIN
TYP
MAX UNITS
ANALOG SWITCH CHARACTERISTICS
Analog Signal Range, V_ANALOG
ON Resistance, R_ON
V_S = ±4.5V, I_COM = 2mA, V_NO or V_NC = 3V
(See Figure 6)
Full
V-
-
V+
V
25
-
44
60
Ω
Full
-
-
80
Ω
R_ON Matching Between Channels, V_S = ±4.5V, I_COM = 2mA, V_NO or V_NC = 3V (Note 5)
25
-
1.3
4
Ω
∆R_ON
Full
-
-
6
Ω
R_ON Flatness, R_FLAT(ON)
V_S = ±4.5V, I_COM = 2mA, V_NO or V_NC = ±3V, 0V
(Note 6)
25
-
Full
-
7.5
9
Ω
-
12
Ω
NO or NC OFF Leakage Current,
I_NO(OFF) or I_NC(OFF)
V_S = ±5.5V, V_COM = ±4.5V, V_NO or V_NC = +4.5V
(Note 7)
25
-0.1
0.002
0.1
nA
Full
-2.5
-
2.5
nA
COM OFF Leakage Current,
I_COM(OFF)
V_S = ±5.5V, V_COM = ±4.5V, V_NO or V_NC = +4.5V
(Note 7)
25
-0.1
0.002
0.1
nA
Full
-2.5
-
2.5
nA
COM ON Leakage Current,
I_COM(ON)
V_S = ±5.5V, V_COM = V_NO or V_NC = ±4.5V (Note 7)
25
-0.1
0.002
0.1
nA
Full
-2.5
-
2.5
nA
DIGITAL INPUT CHARACTERISTICS
Input Voltage High, V_INH, V_ADDH
Input Voltage Low, V_INL, V_ADDL
Input Current, I_ADDH, I_ADDL, I_ENH, V_S = ±5.5V, V_INH, V_ADD = 0V or V+
I_ENL
Input Current, I_ENH, I_LEH
V_S = ±5.5V, V_INH, V_ADD = 0V or V+
Input Current, I_ENL, I_LEL
V_S = ±5.5V, V_INH, V_ADD = 0V or V+
Full
2.4
-
Full
-
-
Full
-0.5
-
Full
-1.5
-
Full
-4
-
-
V
0.8
V
0.5
µA
1.5
µA
4
µA
3
FN6053.3
March 13, 2006