English
Language : 

ISL22349_09 Datasheet, PDF (3/13 Pages) Intersil Corporation – Quad Digitally Controlled Potentiometers
ISL22349
Absolute Maximum Ratings
Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . .-65°C to +150°C
Voltage at any Digital Interface Pin
with Respect to GND . . . . . . . . . . . . . . . . . . . . -0.3V to VCC + 0.3
VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to +6V
Voltage at any DCP Pin with Respect to GND. . . . . . . -0.3V to VCC
IW (10s) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±6mA
Latchup (Note 2) . . . . . . . . . . . . . . . . . . Class II, Level B @ +125°C
ESD Rating
Human Body Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.5kV
Charged Device Model. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1kV
Thermal Information
Thermal Resistance (Typical, Note 1)
θJA (°C/W)
14 Ld TSSOP package . . . . . . . . . . . . . . . . . . . . . . +100
Max Junction Temperature (Plastic Package) . . +50°C to +150°C
Pb-Free Reflow Profile. . . . . . . . . . . . . . . . . . . . . . . . .see link below
http://www.intersil.com/pbfree/Pb-FreeReflow.asp
Recommended Operating Conditions
Ambient Temperature . . . . . . . . . . . . . . . . . . . . . . .-40°C to +125°C
VCC Voltage for DCP Operation . . . . . . . . . . . . . . . . . . 2.7V to 5.5V
Wiper Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -3mA to 3mA
Power Rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5mW
CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product reliability and
result in failures not covered by warranty.
NOTES:
1. θJA is measured with the component mounted on a high effective thermal conductivity test board in free air. See Tech Brief TB379 for details.
2. Jedec Class II pulse conditions and failure criterion used. Level B exceptions are: using a max positive pulse of 6.5V on the SHDN pin, and using
a max negative pulse of -0.8V for all pins.
Analog Specifications Over recommended operating conditions unless otherwise stated.
SYMBOL
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
(Note 13) (Note 3) (Note 13) UNIT
RTOTAL End-to-End Resistance
W option
U option
10
kΩ
50
kΩ
End-to-End Resistance Tolerance
W and U option
-20
+20
%
End-to-End Temperature Coefficient W option
±50
ppm/°C
(Note 11)
U option
±80
ppm/°C
(Note 11)
RW
Wiper Resistance
(Note 13)
CW
Wiper Capacitance
(Note 11)
VCC = 3.3V @ +25°C,
wiper current = VCC/RTOTAL
70
Ω
25
pF
VOLTAGE DIVIDER MODE (measured at RWi, unloaded; i = 0, 1, 2, or 3)
INL
Integral Non-linearity
Monotonic over all tap positions
-1
(Note 8)
1
LSB
(Note 4)
DNL Differential Non-linearity
Monotonic over all tap positions
-0.5
(Note 7)
0.5
LSB
(Note 4)
ZSerror Zero-scale Error
(Note 5)
W option
U option
0
1
5
LSB
(Note 4)
0
0.5
2
FSerror Full-scale Error
(Note 6)
W option
U option
-5
-1
0
LSB
(Note 4)
-2
-1
0
VMATCH DCP to DCP Matching
(Note 9)
Any two DCPs at the same tap position
-2
2
LSB
(Note 4)
TCV
Ratiometric Temperature Coefficient DCP register set to 40 hex
(Note 10)
±4
ppm/°C
3
FN6331.3
May 28, 2009