 English |
|
|
|
|
|
|
|
| DG441 Datasheet, PDF (3/10 Pages) Intersil Corporation – Monolithic, Quad SPST, CMOS Analog Switches | |||
| |||
| ◁ |
DG441, DG442
Absolute Maximum Ratings
V+ to V- . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44.0V
GND to V-. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25V
Digital Inputs, VS, VD (Note 1) . . . . . (V-) -2V to (V+) + 2V or 30mA,
Whichever Occurs First
Continuous Current (Any Terminal) . . . . . . . . . . . . . . . . . . . . . 30mA
Peak Current, S or D (Pulsed 1ms, 10% Duty Cycle Max) . . 100mA
Operating Conditions
Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . . -40oC to 85oC
Voltage Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±20V (Max)
Input Low Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.8V (Max)
Input High Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.4V (Min)
Input Rise and Fall Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . â¤20ns
Thermal Information
Thermal Resistance (Typical, Note 2)
θJA (oC/W)
PDIP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
90
SOIC Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
115
Maximum Junction Temperature (Plastic Packages) . . . . . . .150oC
Maximum Storage Temperature Range . . . . . . . . . . -65oC to 150oC
Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . 300oC
(SOIC - Lead Tips Only)
CAUTION: Stresses above those listed in âAbsolute Maximum Ratingsâ may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this speciï¬cation is not implied.
NOTES:
1. Signals on SX, DX or INX exceeding V+ or V- will be clamped by internal diodes. Limit forward diode current to maximum current ratings.
2. θJA is measured with the component mounted on an evaluation PC board in free air.
Electrical Speciï¬cations (Dual Supply) Test Conditions: V+ = +15V, V- = -15V, VIN = 2.4V, 0.8V, VANALOG = VS, VD,
Unless Otherwise Speciï¬ed
PARAMETER
DYNAMIC CHARACTERISTICS
Turn-ON Time, tON
Turn-OFF Time, tOFF
DG441
DG442
Charge Injection, Q (Figure 2)
OFF Isolation (Figure 4)
Crosstalk (Channel-to-Channel) (Figure 3)
Source OFF Capacitance, CS(OFF)
Drain OFF Capacitance, CD(OFF)
Channel ON Capacitance,
CD(ON) + CS(ON)
DIGITAL INPUT CHARACTERISTICS
Input Current VIN Low, IIL
Input Current VIN High, IIH
ANALOG SWITCH CHARACTERISTICS
Analog Signal Range, VANALOG
Drain-Source ON Resistance, rDS(ON)
TEST CONDITIONS
RL = 1kâ¦, CL = 35pF, VS = ±10V, (Figure 1)
CL = 1nF, VG = 0V, RG = 0â¦
RL = 50â¦, CL = 5pF, f = 1MHz
f = 1MHz, VANALOG = 0 (Figure 5)
VIN Under Test = 0.8V, All Others = 2.4V
VIN Under Test = 2.4V, All Others = 0.8V
IS = 10mA, VD = ±8.5V, V+ = 13.5V,
V- = -13.5V
Source OFF Leakage Current, IS(OFF)
Drain OFF Leakage Current, ID(OFF)
V+ = 16.5V, V- = -16.5V, VD = ±15.5V,
VS = 15.5V
Channel ON Leakage Current,
ID(ON) + IS(ON)
POWER SUPPLY CHARACTERISTICS
Positive Supply Current, I+
Negative Supply Current, I-
V+ = 16.5V, V- = -16.5V, VS = VD = ±15.5V
V+ = 16.5V, V- = -16.5V, VIN = 0V or 5V
Ground Current, IGND
TEMP
(oC)
25
25
25
25
25
25
25
25
Full
Full
Full
25
85
25
85
25
85
25
85
Full
25
Full
Full
(NOTE 3)
MIN
TYP
MAX
-
150
250
-
90
120
-
110
210
-
-1
-
-
60
-
-
-100
-
-
4
-
-
4
-
-
16
-
-0.5 -0.00001 0.5
-0.5 0.00001 0.5
-15
-
15
-
50
85
-
-
100
-0.5
0.01
0.5
-5
-
5
-0.5
0.01
0.5
-5
-
5
-0.5
0.08
0.5
-10
-
10
-
15
100
-1
-0.0001
-
-5
-
-
-100
-15
-
UNITS
ns
ns
ns
pC
dB
dB
pF
pF
pF
µA
µA
V
â¦
â¦
nA
nA
nA
nA
nA
nA
µA
µA
µA
µA
3
|
▷ |
German
Russian
Spanish
Italian
Polish
Chinese
Japanese
Korean
French
Portuguese