X9530 Datasheet, PDF (22/30 Pages) Xicor Inc. – Temperature Compensated Laser Diode Controller

X9530
ABSOLUTE MAXIMUM RATINGS
All voltages are referred to Vss.
Temperature under bias ................... -65°C to +100°C
Storage temperature ........................ -65°C to +150°C
Voltage on every pin except Vcc ................ -1.0V to +7V
Voltage on Vcc Pin .............................................0 to 5.5V
D.C. Output Current at pin SDA ...................... 0 to 5 mA
D.C. Output Current at pins R1, R2,
VRef and VSense.................................... -0.50 to 1 mA
D.C. Output Current at pins I1 and I2 ............... -3 to 3mA
Lead temperature (soldering, 10 seconds) ........ 300°C
OPERATING CONDITIONS
Parameter
Temperature
Temperature while writing to memory
Voltage on Vcc Pin
Voltage on any other Pin
COMMENT
Stresses above those listed under “Absolute Maximum
Ratings” may cause permanent damage to the device.
This is a stress rating only; functional operation of the
device (at these or any other conditions above those
listed in the operational sections of this specification) is
not implied. Exposure to absolute maximum rating
conditions for extended periods may affect device
reliability.
Min.
-40
0
3
-0.3
Max.
+100
+70
5.5
Vcc + 0.3
Units
°C
°C
V
V
ELECTRICAL CHARACTERISTICS
All typical values are for 25°C ambient temperature and 5 V at pin Vcc. Maximum and minimum specifications are
over the recommended operating conditions. All voltages are referred to the voltage at pin Vss unless otherwise
specified. All bits in control registers are “0” unless otherwise specified. 510Ω, 0.1%, resistor connected between R1
and Vss, and another between R2 and Vss unless otherwise specified. 400kHz TTL input at SCL unless otherwise
specified. SDA pulled to Vcc through an external 2kΩ resistor unless otherwise specified. 2-wire interface in “standby”
(see notes 1 and 2 on page 22), unless otherwise specified. WP, A0, A1, and A2 floating unless otherwise specified.
VRef pin unloaded, unless otherwise specified.
Symbol
Iccstby
Iccfull
Iccwrite
I_PLDN
V_ILTTL
V_IHTTL
I_INTTL
V_OLSDA
I_OHSDA
V_ILCMOS
Parameter
Min Typ Max Unit
Test Conditions / Notes
Standby current into Vcc
pin
2
mA R1 and R2 floating, VRef unloaded.
Full operation current into
Vcc pin
9
mA 2-wire interface reading from
memory, I₁ and I₂ both connected to
Vss, DAC input bytes: FFh, VRef
unloaded.
Nonvolatile Write current
into Vcc pin
4
mA Average from START condition until
t_WP after the STOP condition
WP: Vcc, R1 and R2 floating,
VRef unloaded.
On-chip pull down
0
current at WP, A0, A1,and
A2
1
20
µA V(WP), V(A0), V(A1), and V(A2) from
0V to Vcc
SCL and SDA, input Low
voltage
0.8
V
SCL and SDA, input High 2.0
V
voltage
SCL and SDA input
-1
current
10
µA Pin voltage between 0 and Vcc, and
SDA as an input.
SDA output Low voltage
0
0.4
V I(SDA) = 2 mA
SDA output High current
0
100 µA V(SDA) = Vcc
WP, A0, A1, and A2 input
0
Low voltage
0.2 x V
Vcc
22
FN8211.0
March 10, 2005