ISL59111 Datasheet, PDF (2/10 Pages) Intersil Corporation – 8MHz Rail-to-Rail Composite Video Driver

ISL59111
Absolute Maximum Ratings (T_A = +25°C)
Supply Voltage from V_S+ to GND . . . . . . . . . . . . . . . . . . . . . . . 3.6V
Input Voltage . . . . . . . . . . . . . . . . . . . . . . . V_S+ +0.3V to GND -0.3V
Continuous Output Current . . . . . . . . . . . . . . . . . . . . . . . . . . . 40mA
Power Dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Curves
Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . .-65°C to +125°C
Ambient Operating Temperature . . . . . . . . . . . . . . . .-40°C to +85°C
Operating Junction Temperature . . . . . . . . . . . . . . . . . . . . . . +125°C
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
IMPORTANT NOTE: All parameters having Min/Max specifications are guaranteed. Typ values are for information purposes only. Unless otherwise noted, all tests are
at the specified temperature and are pulsed tests, therefore: T_J = T_C = T_A
Electrical Specifications V_S+ = 3.3V, T_A = +25°C, R_L = 150Ω to GND, C_L = 0.1µF, unless otherwise specified.
DESCRIPTION
PARAMETER
CONDITIONS
MIN TYP
MAX
UNIT
INPUT CHARACTERISTICS
V_CC
I_DD-ON
I_DD-OFF
V_OLS
V_CLAMP
I_{CLAMP_CHG}
I_{CLAMP_DCHG}
R_IN
A_V
A_SAG
PSRR
Supply Voltage Range
Quiescent Supply Current
Shutdown Supply Current
Output Level Shift Voltage
Input Voltage Clamp
Clamp Charge Current
Clamp Discharge Current
Input Resistance
Voltage Gain
SAG Correction DC Gain to V_OUT
DC Power Supply Rejection
V_OH
I_SC
Output Voltage High Swing
Output Short-Circuit Current
I_ENABLE
V_IL
V_IH
R_OUT
Enable Current
Disable Threshold
Enable Threshold
Shutdown Output Impedance
2.5
3.6
V
V_IN = 500mV, EN = V_DD, no load
EN = 0V
2
2.75
mA
3
µA
V_IN = 0V, no load
I_IN = -1mA
V_IN = V_CLAMP - 100mV
V_IN = 500mV
0.5V < V_IN < 1.0V
R_L = 150Ω
SAG open
60
130
200
mV
-40
-15
+10
mV
-6
-3
mA
2.5
5
7.5
µA
0.5
3
MΩ
1.95
2.0
2.04
V/V
2.25
V/V
V_DD = 2.7V to 3.3V
43
63
dB
V_IN = 2V, R_L = 150Ω to GND
2.85
3.2
V
V_IN = 2V, to GND through 10Ω
-94
-65
mA
V_IN = 100mV, out short to V_DD through 10Ω 65
115
mA
±3.3V, enable pin = 0V
-3
0
+3
µA
V_DD = 2.7V to 3.3V
V_DD = 2.7V to 3.3V
EN = 0V DC
0.8
V
1.6
V
3.6
4.5
5.9
kΩ
EN = 0V, f = 4.5MHz
3.4
kΩ
AC PERFORMANCE
BW
±0.1dB Bandwidth
BW
-3dB Bandwidth
Normalized Stopband Gain
R_L = 150Ω, C_L = 5pF
R_L = 150Ω, C_L = 5pF
f = 27MHz
4
8
-24.2
MHz
MHz
dB
dG
Differential Gain
NTSC and PAL DC coupled
0.10
%
NTSC and PAL AC coupled
0.84
%
dP
Differential Phase
NTSC and PAL DC coupled
0.05
°
NTSC and PAL AC coupled
0.62
°
D/DT
Group Delay Variation
f = 100kHz, 5MHz
5.4
ns
SNR
Signal To Noise Ratio
100% white signal
65
dB
T_ON
Enable Time
V_IN = 500mV, V_OUT to 1%
200
ns
2
FN6172.3
August 29, 2006