ISL6721_07 Datasheet, PDF (18/21 Pages) Intersil Corporation – Flexible Single Ended Current Mode PWM Controller

ISL6721
Regulation Performance
TABLE 1. OUTPUT LOAD REGULATION, V_IN = 48V
I_OUT (A), 3.3V I_OUT (A), 1.8V V_OUT (V), 3.3V V_OUT (V), 1.8V
0
0.030
3.351
1.825
0.39
0.030
3.281
1.956
0.88
0.030
3.251
1.988
1.38
0.030
3.223
2.014
1.87
0.030
3.204
2.029
2.39
0.030
3.185
2.057
2.89
0030
3.168
2.084
3.37
0.030
3.153
2.103
0
0.52
3.471
1.497
0.39
0.52
3.283
1.800
0.88
0.52
3.254
1.836
1.38
0.52
3.233
1.848
1.87
0.52
3.218
1.855
2.39
0.52
3.203
1.859
2.89
0.52
3.191
1.862
0
1.05
3.619
1.347
0.39
1.05
3.290
1.730
0.88
1.05
3.254
1.785
1.38
1.05
3.235
1.805
1.87
1.05
3.220
1.814
2.39
1.05
3.207
1.820
0
1.55
3.699
1.265
0.39
1.55
3.306
1.682
0.88
1.55
3.260
1.750
1.38
1.55
3.239
1.776
1.87
1.55
3.224
1.789
0
2.07
3.762
1.201
0.39
2.07
3.329
1.645
0.88
2.07
3.270
1.722
1.38
2.07
3.245
1.752
0
2.62
3.819
1.142
0.39
2.62
3.355
1.612
0.88
2.62
3.282
1.697
0
3.14
3.869
1.091
.39
3.14
3.383
1.581
Waveforms
Typical waveforms can be found in Figures 10 through 12.
Figure 10 shows the steady state operation of the sawtooth
oscillator waveform at RTCT (Trace 2), the SYNC output
pulse (Trace 1), and the GATE output to the converter FET
(Trace 3). Figure 11 shows the converter behavior while
operating in an overcurrent fault condition. Trace 1 is the
soft-start voltage, which increases from 0V to 4.5V, at which
point the OC fault function is enabled. The OC condition is
detected and the soft-start capacitor is discharged to the
4.375V OC fault threshold at which point the IC enters the
fault shutdown mode. Trace 2 shows the behavior of the
timing capacitor voltage during a shutdown fault. Most of the
functions of the IC are de-powered during a fault, and the
oscillator is among those functions. During a fault, the IC is
turned off until the restart delay has timed out. After the
delay, power is restored and the IC resumes normal
operation. Trace 3 is the GATE output during the soft-start
cycle and OC fault.
NOTE:
Trace 1: SYNC Output
Trace 2: RTCT Sawtooth
Trace 3: GATE Output
FIGURE 10. TYPICAL WAVEFORMS
NOTE:
Trace 1: SS
Trace 2: RTCT Sawtooth
Trace 3: GATE Output
FIGURE 11. SOFT-START WITH OVERCURRENT FAULT
Figure 12 shows the switching FET waveforms during
steady state operation. Trace 1 is drain - source voltage and
Trace 2 is gate - source voltage.
18
FN9110.4
April 13, 2007