HSP48410 Datasheet, PDF (10/12 Pages) Intersil Corporation – Histogrammer/Accumulating Buffer

HSP48410
Absolute Maximum Ratings
Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +8.0V
Input, Output Voltage . . . . . . . . . . . . . . . . . .GND-0.5V to V_CC+0.5V
ESD Classification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Class 1
Operating Conditions
Voltage Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +5V ±5%
Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0^oC to 70^oC
Thermal Information
Thermal Resistance (Typical, Note 3)
θ_JA (^oC/W) θ_JC (^oC/W)
PGA Package. . . . . . . . . . . . . . . . . . . . N/A
8.0^oC/W
PLCC Package. . . . . . . . . . . . . . . . . . .
34
N/A
Maximum Storage Temperature Range . . . . . . . . . . -65^oC to 150^oC
Maximum Junction Temperature . . . . 175^oC (PGA), 150^oC (PLCC)
Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . .300^oC
(PLCC - Lead Tips Only)
Die Characteristics
Gate Count . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3500 Gates
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTE:
3. θ_JA is measured with the component mounted on an evaluation PC board in free air.
DC Electrical Specifications
PARAMETER
SYMBOL
MIN
MAX
UNITS
TEST CONDITIONS
Logical One Input Voltage
Logical Zero Input Voltage
High Level Clock Input
Low Level Clock Input
Output High Voltage
Output Low Voltage
Input Leakage Current
I/O Leakage Current
Standby Supply Current
V_IH
2.0
-
V
V_CC = 5.25V
V_IL
-
0.8
V
V_CC = 4.75V
V_IHC
3.0
-
V
V_CC = 5.25V
V_ILC
-
0.8
V
V_CC = 4.75V
V_OH
2.6
-
V
I_OH = -400µA, V_CC = 4.75V
V_OL
-
0.4
V
I_OL = +2.0mA, V_CC = 4.75V
I_L
-10
10
µA
V_IN = V_CC or GND, V_CC = 5.25V
I_O
-10
10
µA
V_OUT = V_CC or GND, V_CC = 5.25V
I_CCSB
D-
500
µA
V_IN = V_CC or GND, V_CC = 5.25V,
Outputs Open
Operating Power Supply Current
NOTES:
I_CCOP
-
396
mA
f = 33 MHz, V_IN = V_CC or GND
V_CC = 5.25V (Notes 4, 5)
4. Power supply current is proportional to operating frequency. Typical rating for I_CCOP is 12mA/MHz.
5. Maximum junction temperature must be considered when operating part at high clock frequencies.
Capacitance T_A = 25^oC, Not tested, but characterized at initial design and at major process or design changes.
PARAMETER
SYMBOL
MIN
MAX
UNITS
TEST CONDITIONS
Input Capacitance
Output Capacitance
C_IN
-
C_OUT
-
12
pF
FREQ = 1 MHz, V_CC = Open, all
12
pF
measurements are referenced to
device ground.
AC Electrical Specifications V_CC = 5V ± 5%, T_A = 0^oC to 70^oC (Note 6)
PARAMETER
Clock Period
Clock Low
Clock High
DIN Setup
DIN0-23 Hold
Clock to DIO0-23 Valid
FC Pulse Width
FCT0-2 Setup to LD
SYMBOL
t_CP
t_CH
t_CL
t_DS
t_DH
t_DO
t_FL
t_FS
NOTES
-40 (40 MHz)
MIN MAX
25
-
10
-
10
-
12
-
0
-
-
15
35
-
10
-
-33 (33 MHz)
MIN MAX
30
-
12
-
12
-
13
-
0
-
-
19
35
-
10
-
UNITS
ns
ns
ns
ns
ns
ns
ns
ns
10