AUIPS6125RTRL Datasheet, PDF (4/17 Pages) Infineon Technologies AG – LOW EMI CURRENT SENSE HIGH SIDE SWITCH

AUIPS6125R
Static Electrical Characteristics
Tj=-40°C..150°C, Vcc=6..18V (unless otherwise specified)
Symbol Parameter
Min. Typ. Max.
Vcc op.
Operating voltage range
5.8

18
Rds(on)
ON state resistance Tj=25°C

3.9

ON state resistance Tj=150°C(2)

6
8
Icc off
Supply leakage current

1
3
Iout off
Output leakage current

1
3
Iin on
Input current when device on
1
2.7
6
Vbr
Vcc to Vout breakdown voltage
30.5 35
50
35
39
55
Vih (3)
High level Input threshold voltage
4.5 5.4 6.2
Vil (3)
Low level Input threshold voltage
4
5
5.8
Rds(on) rev Reverse On state resistance Tj=25°C

4
7
Vf
Forward body diode voltage Tj=25°C

0.8 0.9
Forward body diode voltage Tj=125°C

0.6 0.8
Rin
Input resistor
115 200 300
(2) Guaranteed by design
(3) Input thresholds are measured directly between the input pin and the tab.
Units
V
m
µA
mA
V
m
V

Test Conditions
Ids=10A
Vin=Vcc=14V,Vifb=Vgnd
Vout=Vgnd, Tj=25°C
Vcc-Vin=14V
Tj=25°C, Id=10mA
Tj=150°C, Id=10mA
Id=20mA
Isd=10A, Vin-Vcc>8V
If=10A
Built-in
Switching Electrical Characteristics
Vcc=14V, Resistive load=1, Tj=25°C
Symbol Parameter
tdon
Turn on delay time
Tr
Rise time from 20% to 80% of Vcc
tdoff
Turn off delay time
Tf
Fall time from 80% to 20% of Vcc
Min.
5
5
20
5
Typ.
40
15
110
15
Max.
150
45
200
45
Units
µs
Test Conditions
See fig. 1
Protection Characteristics
Tj=-40°C..150°C, Vcc=6..18V (unless otherwise specified)
Symbol Parameter
Tsd
Over temperature threshold(2)
Isd
Over-current shutdown
Ifb after an over-current or an over-
I fault
temperature (latched)
Min. Typ. Max. Units
150 165 
°C
60 90 120
A
9
20
27
mA
Test Conditions
See fig. 3
See fig. 3 and page 6
See fig. 3,
Vcc-Vifb>4V
Psd_rst
Time to reset Psd
Psd_UV Time to shut down when Vcc-Vin<Vil
I in rst
Input current to reset the protection
Vin reset
Input voltage between Vcc and Vin to
Reset the latch
T reset
(2) Guaranteed by design

26

0.01 0.06 0.2
40


0.8 1.8
3
6

200
ms
See page 8
µA
V
µs See figure 3
Current Sensing Characteristics
Tj=-40°C..150°C, Vcc=6..18V (unless otherwise specified)
Symbol Parameter
Min. Typ.
Ratio
I load / Ifb current ratio
5000 6200
Ratio_Cold
Ratio_Hot
I offset
Ratio drift between 25°C to -40°C
Ratio drift between 25°C to 125°C
Load current offset
-3 -0.8
-0.5 2.3
-0.15 0
Max.
7600
1
5
0.15
Units Test Conditions
Iload=60A at Vcc=14V / Vcc-Vifb>5V
Iload=30A at Vcc=6V/ Vcc-Vifb>3.5V
After 2ms, See page 7
%
Ratio@-40°/Ratio@25°
Ratio@125°/Ratio@25°
A After 2ms
4 Rev 1.3
2016-11-08