IC-MFL Datasheet, PDF (6/13 Pages) IC-Haus GmbH – 8-/12-FOLD FAIL-SAFE LOGIC N-FET DRIVER

iC-MFL / iC-MFLT
8-/12-FOLD FAIL-SAFE LOGIC N-FET DRIVER
Rev C1, Page 6/13
ELECTRICAL CHARACTERISTICS
Operating Conditions: VCC = 5 V ±10 %, Tj = -40...125 °C unless otherwise stated
Item Symbol Parameter
No.
Conditions
Total Device
001 VCC
Permissible Supply Voltage
002 I(VCC) Supply Current in VCC
(No load)
iC-MFL
iC-MFLT
003 I(VCC) Error Current in VCC
VCC = 5 V, one output at 18 V
004 I(GND) Current in GND
(No load)
iC-MFL
iC-MFLT
005 I(GNDR) Current in GNDR
(No load, all OUTx = hi)
iC-MFL
iC-MFLT
Current Driver OUT1...8/12
101 I(OUTx) Current in I(OUTx)
V() = 18 V
VCC = 5 V
102 U(OUTx) permitted voltage
T < 100 ms, duty cycle < 2 %
103 Vc()lo
Clamp Voltage lo referenced to I() = -10 mA
the lower voltage of GND, GNDR
104 Vs()hi
Saturation Voltage hi referenced Vs()hi = VCC – V();
to VCC
I() = -0.5 mA
I() = -2 mA
105 Vs()lo
Saturation Voltage lo referenced I() = 0.5 mA
to GND
I() = 2 mA
106 Rpd()
Pull-Down Resistor at OUTx
referenced to GNDR
V(GND) > Vtr(GND)
107 Isc()lo
Short circuit current lo
V() = 0.8 V...VCC
108 Isc()hi
Short circuit current hi
V() = 0...VCC – 0.8 V
109 Vsh()
Output Voltage at short circuit of At two different input signals hi
two outputs
and lo
Input IN1...8/12, EN
201 Vc()hi
Clamp Voltage hi
I() = 10 mA
202 Vc()lo
Clamp Voltage lo referenced to I() = -10 mA
the lower voltage of GND, GNDR
203 Vt()hi
Threshold Voltage hi
204 Vt()lo
Threshold Voltage lo
205 Vt()hys Input Hysteresis
Vt()hys = Vt()hi – Vt()lo
206 Ipd1()
Pull-Down Current 1
0.4 V < V() < Vt()hi
207 Ipd2()
Pull-Down Current 2
V() > 1.4 V
208 Cin()
Input Capacitance
209 Ileak()
Input Leakage Current
VCC = 0 V, V() = 0...5.5 V
Supply Monitor
301 VCCon Turn-On Threshold VCC
302 VCCoff Turn-Off Threshold VCC
Decreasing voltage VCC
303 VCChys Hysteresis
VCChys = VCCon – VCCoff
Ground Monitor GND, GNDR
401 Vtg()hi
Threshold Voltage hi GND Moni- Referenced to GNDR
tor
402 Vtg()lo
Threshold Voltage lo GND Moni- Referenced to GNDR
tor
403 Vtg()hys Hysteresis
Vt()hys = Vt()hi - Vt()lo
404 Vtr()hi
Threshold Voltage hi GNDR Mon- Referenced to GND
itor
405 Vtr()lo
Threshold Voltage lo GNDR Mon- Referenced to GND
itor
Tj Fig.
Unit
°C
Min. Typ. Max.
4.5
5
5.5
V
1.5
7
mA
10
mA
-50
mA
-6
mA
-9
mA
-4
-0.3 mA
-6
mA
20
100 mA
18
V
-3
-0.4
V
0.2
V
0.8
V
0.2
V
0.8
V
12
30
70
kΩ
2
3.6
6
mA
-6
-3
-2
mA
1.1
V
6
V
-3
-0.4
V
1.1
1.4
V
0.8
1.1
V
200
400 mV
4 150 225 350 µA
4
20
45
70
µA
20
pF
-10
10
µA
3.7
4.4
V
3.2
4.1
V
100 200 600 mV
270 mV
50
mV
5
80
mV
270 mv
50
mV