HCPL-3100 Datasheet, PDF (6/10 Pages) Agilent(Hewlett-Packard) – Power MOSFET/IGBT Gate Drive Optocouplers

Switching Specifications (T_A = 25°C)
Parameter
Sym.
Device Min. Typ. Max. Units
Test Conditions
Fig. Note
Propagation
t_PLH
Delay Time to
High Output
Level
Propagation
t_PHL
Delay Time to
Low Output
Level
HCPL-3100 -
HCPL-3101 -
HCPL-3100 -
HCPL-3101 -
1
2
µs I_F = 10 mA V_CC = 24 V,
9, 2, 6
V_O1 = 24 V,
25,
0.3 0.5 µs I_F = 5 mA R_G = 47 Ω,
26,
C_G = 3000 pF 27
1
2
µs I_F = 10 mA
0.3 0.5 µs I_F = 5 mA
Rise Time
t_r
HCPL-3100 -
0.2 0.5 µs I_F = 10 mA
HCPL-3101
I_F = 5 mA
Fall Time
t_f
HCPL-3100 -
0.2 0.5 µs I_F = 10 mA
HCPL-3101
I_F = 5 mA
Output High
|CM_H| HCPL-3100 1500 5000
- V/µs I_F = 10 mA V_CM = 600 V 10
2
Level Common
(peak),
Mode Transient
HCPL-3101
I_F = 5mA V_CC = 24 V
Immunity
V_O1 = 24 V
∆V_02H = ∆V_02L
Output Low
|CM_L|
1500 5000 - V/µs I_F = 0 mA
= 2.0 V
Level Common
Mode Transient
Immunity
Packaging Characteristics
Parameter
Input-Output Momentary
Withstand Voltage*
Resistance (Input-Output)
Capacitance (Input-Output)
Sym.
V_ISO
Min. Typ.
5000
Max. Units
V rms
R_I-O
5x10¹⁰ 10¹¹
–
Ω
C_I-O
–
1.2
–
pF
Test Conditions
Fig. Note
RH = 40% to 60%
4, 5
t = 1 min, T_A = 25°C
V_I-O = 500 V, T_A = 25°C
4
RH = 40% to 60%
f = 1 MHz
4
*The Input-Output Momentary Withstand Voltage is a dielectric voltage rating that should not be interpreted as an input-output
continuous voltage rating. For the continuous voltage rating refer to the VDE 0884 Insulation Characteristics Table (if applicable), your
equipment level safety specification, or HP Application Note 1074, “Optocoupler Input-Output Endurance Voltage.”
Notes:
1. Derate absolute maximum ratings with ambient temperatures as shown in Figures 11 and 12.
2. A bypass capacitor of 0.01 µF or more is needed near the device between V_CC and GND when measuring output and transfer
characteristics.
3. I_FLH represents the forward current when the output goes from low to high.
4. Device considered a two terminal device; pins 1-4 are shorted together and pins 5-8 are shorted together.
5. For devices with minimum V_ISO specified at 5000 V rms, in accordance with UL 1577, each optocoupler is proof-tested by applying an
insulation test voltage ≥ 6000 V rms for one second (leakage current detection limit, I_I-O ≤ 200 µA).
6. The t_PLH and t_PHL propagation delays are measured from the 50% level of the input pulse to the 50% level of the output pulse.
7. R₂ limits the Q1 and Q2 peak currents. For more applications and circuit design information see Application Note “Power Transistor
Gate/Base Drive Optocouplers.”
1-343