HCPL-3000 Datasheet, PDF (5/9 Pages) Agilent(Hewlett-Packard) – Power Bipolar Transistor Base Drive Optocoupler

Switching Specifications (T_A = 25°C)
Parameter
Sym. Min. Typ. Max. Units
Test Conditions
Fig. Note
Propagation Delay
Time to High Output
Level
t_PLH
-
2
5
µs V_CC = 6 V, I_F = 5 mA,
7, 2, 6
R_L1 = 5 Ω, R_L2 = 10 Ω
24,
25
Propagation Delay Time t_PHL -
2
5
to Low Output Level
Rise Time
t_r
- 0.2 1
Fall Time
t_f
- 0.1 1
Output High Level
Common Mode
Transient Immunity
|CM_H| 1500 -
-
V/µs V_CM = 600 V Peak,
8
2
I_F = 5mA, R_L1 = 470 Ω,
R_L2 = 1 kΩ, ∆V_02H = 0.5 V
Output Low Level
Common Mode
Transient Immunity
|CM_L| 1500 -
-
V/µs V_CM = 600 V Peak,
I_F = 0 mA, R_L1 = 470 Ω,
R_L2 = 1 kΩ, ∆V_02L = 0.5 V
Package Characteristics
Parameter
Sym. Min. Typ. Max. Units
Test Conditions
Fig. Note
Input-Output Momentary V_ISO 5000
Withstand Voltage*
V rms RH = 40% to 60%,
4, 5
t = 1 min., T_A = 25°C
Resistance
R_I-O 5x10¹⁰ 10¹¹
–
Ω
V_I-O = 500 V, T_A = 25°C,
4
(Input-Output)
RH = 40% to 60%
Capacitance
C_I-O
–
1.2
–
pF f = 1 MHz
4
(Input-Output)
*The Input-Output Momentary Withstand Voltage is a dielectric voltage rating that should not be interpreted as an input-output
continuous voltage rating. For the continuous voltage rating refer to the VDE 0884 Insulation Characteristics Table (if applicable), your
equipment level safety specification, or HP Application Note 1074, “Optocoupler Input-Output Endurance Voltage.”
Notes:
1. Derate absolute maximum ratings with ambient temperatures as shown in Figures 9, 10, and 11.
2. A bypass capacitor of 0.01 µF or more is needed near the device between V_CC and GND when measuring output and transfer
characteristics.
3. I_FLH represents the forward current when the output goes from low to high.
4. Device considered a two terminal device; pins 1-4 are shorted together and pin 5-8 are shorted together.
5. For devices with minimum V_ISO specified at 5000 V rms, in accordance with UL1577, each optocoupler is proof-tested by applying an
insulation test voltage ≥ 6000 V rms for one second (leakage current detection limit, I_I-O ≤ 200 µA).
6. The t_PLH and t_PHL propagation delays are measured from the 50% level of the input pulse to the 50% level of the output pulse.
7. R₁ sets the base current (I_O1 in Figure 1) supplied to the power bipolar device. R₂ limits the peak current seen by Q2 when the device
is turning off. For more applications and circuit design information see Application Note “Power Transistor Gate/Base Drive
Optocouplers.”
1-333