HCPL-2201 Datasheet, PDF (11/15 Pages) Agilent(Hewlett-Packard) – Very High CMR, Wide VCC Logic Gate Optocouplers

Package Characteristics
Parameter
Sym. Min. Typ. Max. Units
Test Conditions
Fig. Note
Input-Output Momentary
Withstand _HCNW22XX
Voltage^*
V_ISO 2500
5000
V rms RH < 50%, t = 1 min.
T_A = 25°C
5, 10
5, 11
Input-Output Resistance
R_I-O
10¹²
Ω
V_I-O = 500 Vdc
5
HCNW22XX
10¹² 10¹³
T_A = 25°C
10¹¹
T_A = 100°C
Input-Output Capacitance C_I-O
0.6
pF
f = 1 MHz,
5
HCNW22XX
0.5 0.6
T_A = 25°C ^VI-O ^{= 0 Vdc}
Input-Input Insulation
I_I-I
0.005
µA Relative Humidity = 45%,
12
Leakage Current
t = 5 s, V_I-I = 500 V
Resistance (Input-Input)
R_I-I
10¹¹
Ω V_I-I = 500 V
12
Capacitance (Input-Input)
C_I-I
0.25
pF f = 1 MHz
12
*The Input-Output Momentary Withstand Voltage is a dielectric voltage rating that should not be interpreted as an input-output
continuous voltage rating. For the continuous voltage rating refer to the VDE 0884 Insulation Characteristics Table (if applicable),
your equipment level safety specification or HP Application Note 1074 entitled “Optocoupler Input-Output Endurance Voltage,”
publication number 5963-2203E.
Notes:
1. Each channel.
2. Derate total package power dissipation, P_T, linearly above 70°C free-air temperature at a rate of 4.5 mW/°C.
3. Duration of output short circuit time should not exceed 10 ms.
4. For single devices, input capacitance is measured between pin 2 and pin 3.
5. Device considered a two-terminal device: pins 1, 2, 3, and 4 shorted together and pins 5, 6, 7, and 8 shorted together.
6. The t_PLH propagation delay is measured from the 50% point on the leading edge of the input pulse to the 1.3 V point on the
leading edge of the output pulse. The t_PHL propagation delay is measured from the 50% point on the trailing edge of the input
pulse to the 1.3 V point on the trailing edge of the output pulse.
7. CM_H is the maximum slew rate of the common mode voltage that can be sustained with the output voltage in the logic high state,
V_O > 2.0 V. CM_L is the maximum slew rate of the common mode voltage that can be sustained with the output voltage in the logic
low state, V_O < 0.8 V.
8. For HCPL-2202/12, V_O is on pin 6.
9. Use of a 0.1 µF bypass capacitor connected between pins 5 and 8 is recommended.
10. In accordance with UL 1577, each optocoupler is proof tested by applying an insulation test voltage ≥ 3000 V rms for one second
(leakage detection current limit, I_I-O ≤ 5 µA). This test is performed before the 100% production test for partial discharge (Method
b) shown in the VDE 0884 Insulation Characteristics Table, if applicable.
11. In accordance with UL 1577, each optocoupler is proof tested by applying an insulation test voltage ≥ 6000 V rms for one second
(leakage detection current limit, I_I-O ≤ 5 µA). This test is performed before the 100% production test for partial discharge (Method
b) shown in the VDE 0884 Insulation Characteristics Table.
12. For HCPL-2231/32 only. Measured between pins 1 and 2, shorted together, and pins 3 and 4, shorted together.
1-141