EMX2C9100-23B Datasheet, PDF (7/8 Pages) Hamamatsu Corporation – Multiply faster

Specifications
Type number
Camera head type
Window
C9100-23B(ImagEM X2)
Hermetic vacuum-sealed air/water-cooled head _*¹
Anti-reflection (AR) coatings on both sides, single window
AR mask
Yes
Imaging device
Electron Multiplying Back-Thinned Frame Transfer CCD
Effective number of pixels
512 (H) × 512 (V)
Cell size
16 μm (H) × 16 μm (V)
Effective area
8.19 mm (H) × 8.19 mm (V)
Pixel clock rate EM-CCD readout
22 MHz, 11 MHz, 0.6875 MHz
Normal-CCD readout
0.6875 MHz
EM (electron multiplying) gain (typ.) _*2
Ultra-low light detection
4× to 1200×
Photon Imaging mode (1, 2, 3)
Fastest readout speed
70.4 frames/s to 1076 frames/s
Readout noise
EM-CCD EM gain 4×
36 electrons (at 22 MHz)
(rms) (typ.)
readout
25 electrons (at 11 MHz)
8 electrons (at 0.6875 MHz)
EM gain 1200×
1 electron max. (at 22 MHz)
1 electron max. (at 11 MHz)
1 electron max. (at 0.6875 MHz)
Normal CCD readout
8 electrons (at 0.6875 MHz)
Full well capacity EM-CCD mode
370 000 electrons (CIC serious consideration)
(typ.) _*3
Analog gain
Normal-CCD mode
EM-CCD 22 MHz
140 000 electrons (Full well capacity serious consideration)
1×
readout 11 MHz/0.6875 MHz
0.5×, 1×
Normal CCD readout
1×, 2×, 3×, 4×, 5×
Cooling method / Forced- at temperature control
temperature _*⁴
air cooled at slow scan
-65 ˚C stabilized (0 ˚C to +30 ˚C)
-75 ˚C (Room temperature : Stable at +20 ˚C, No binning)
at maximum cooling typ.
-80 ˚C (Room temperature: Stable at +20 ˚C )
Water
at temperature control
-80 ˚C stabilized (Water temperature: +20 ˚C)
cooled _*5 at maximaum cooling typ.
Temperature stability (typ.)
-100 ˚C (Water temperature: lower than +10 ˚C)
±0.01 ˚C
Dark current
(typ.) _*⁶
Forced-air cooled (-65 ˚C)
Water cooled (-80 ˚C)
0.005 electron/pixel/s
0.0005 electron/pixel/s
Clock induced charge (typ.)
0.0015 events/pixel/frame
Exposure time _*7 Internal synchronus mode
13.9 ms to 1 s (22 MHz)
27.2 ms to 2 h (11 MHz)
421.5 ms to 2 h (0.6875 MHz)
External trigger mode
10 μs to 1 s (22 MHz)
10 μs to 2 h (11 MHz, 0.6875 MHz)
A/D converter
16 bit
Output signal / External control
IEEE1394b
Sub-array
Binning
External trigger mode _*⁹
Every 16 lines (horizontal, vertical) size, position can be set
2×2, 4×4, 8×8, 16×16 _*⁸
Edge trigger, Level trigger, Start trigger, Synchronous readout trigger
Trigger output _*9
Image processing features (real-time)
Exposure timing output, Programmable timing output (Delay and pulse length are variable.), Trigger ready output
Background subtraction, Shading correction,
EM gain protection
Recursive filter, Frame averaging, Spot noise reducer _*10
EM warning mode, EM protection mode
EM gain readjustment
Available
Lens mount
C-mount
Power requirements
AC 100 V to 240 V, 50 Hz / 60 Hz
Power consumption
Approx. 140 VA
Ambient storage temperature
-10 ˚C to + 50 ˚C
Ambient operating temperature
0 ˚C to + 40 ˚C
Performance guaranteed temperature
0 ˚C to + 30 ˚C
Ambient operating/storage humidity
70 % max. (with no condensation)
*^{1 The hermetic sealed head maintains a high degree of vacuum, 10-8 Torr, without re-evacuation.}
*^{2 Even with electron multiplying gain maximum, dark signal is kept at a low level during low light imaging.}
*^{3 Linearity is not assured when full well capacity is over 370 000 electrons, because of CCD performance.}
*^{4 The cooling temperature may not reach to this temperature; it depends on the operation condition.}
*^{5 Water volume 0.5 liter/min.}
*^{6 Typical thermal charge value (not guaranteed).}
*^{7 Image smearing may appear when the exposure time is short.}
*^{8 8 × 8 and 16 × 16 binning are available on special order. Please consult with our sales office.}
*^{9 C-MOS 3.3 V with reversible polarity.}
*^{10 Recursive filter, frame averaging, and spot noise reducer cannot be used simultaneously.}