C9312SK-06 Datasheet, PDF (4/6 Pages) Hamamatsu Corporation – Flat panel sensor High-speed, High reliability, 110 kV (X-ray tube voltage) proof

Flat panel sensor C9312SK-06
s System requirements
To operate C9312SK-06 at full performance, the following system and peripherals are required.
· PC: IBM compatible PC running on Windows XP
· Digital frame grabber card: Monochrome 32 bits or more, pixel clock 33.3 MHz or more, LVDS interface synchronous signal (See
the frame grabber manual.)
· Power source: A. vdd = +5.0 ± 0.1 V (1.8 A), D. vdd = +5.0 ± 0.1 V (0.5 A).
Please use a series power supply. (Avoid using a switching power supply.) A power cable (terminated with an DB-25SF-N plug
with right angle type shell at one end and open at the other end; 2 m; see Table 2.), an external trigger cable (terminated with an
FFA.OS.302.CLAC37 plug at one end and open at the other end; 5 m; see table 3.) and an earth cable (AWG 18; 4 m) comes
supplied with C9312SK-06. An optional frame grabber cable for interface with the 80-pin receptacle (see Table 1) on C9312SK-
06 is also available for synchronous signal, video output and external control.
The voltages described above are specified at the flat panel sensor side. The impedance of the power cable attached with the
flat panel sensor is low enough but it causes 0.1 V approx. drop. Therefore the voltage at the power source side should be set
0.1 V higher than the voltage specified above. Install a noise filter on the AC power input line to prevent surges on the AC line.
To supply the synchronous signal through ExtTrgGrb, apply high level of TTL to ExtTrgLemo and IntExt, or leave them without
connection. On the contrary, to use ExtTrgLemo, set high level to ExtTrgGrb and IntExt, or leave them without connection. The
earth terminal must be connected to a stable earth point to eliminate noise from surroundings.
Table 1: Pin assignment of 80-pin receptacle
Pin No.
Signal
1
A_Data1+ (LSB)
2
A_Data1- (LSB)
3
A_Data2+
4
A_Data2-
5
A_Data3+
6
A_Data3-
7
A_Data4+
8
A_Data4-
9
A_Data5+
10
A_Data5-
11
A_Data6+
12
A_Data6-
13
A_Data7+
14
A_Data7-
15
A_Data8+
16
A_Data8-
17
A_Data9+
18
A_Data9-
19
A_Data10+
20
A_Data10-
21
A_Data11+
22
A_Data11-
23
A_Data12+ (MSB)
24
A_Data12- (MSB)
25
Reserved
26
Reserved
27
Reserved
28
Reserved
29
Reserved
30
Reserved
31
Reserved
32
Reserved
33
IntExt (TTL)
34
Reserved
35
Vsync+
36
Vsync-
37
Hsync+
38
Hsync-
39
Pclk+
40
Pclk-
Unless otherwise noted signal, signal level is LVDS.
80-pin receptacle: PCS-E80LMD made by Honda Tsushin Kogyo Co., Ltd.
Mating plug: PCS-E80FA made by Honda Tsushin Kogyo Co., Ltd.
Pins described “Reserved” are prepared for an extension of the future.
Do not connect any signal or power or GND, etc. to this plug.
Pin No.
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
Signal
B_Data1+ (LSB)
B_Data1- (LSB)
B_Data2+
B_Data2-
B_Data3+
B_Data3-
B_Data4+
B_Data4-
B_Data5+
B_Data5-
B_Data6+
B_Data6-
B_Data7+
B_Data7-
B_Data8+
B_Data8-
B_Data9+
B_Data9-
B_Data10+
B_Data10-
B_Data11+
B_Data11-
B_Data12+ (MSB)
B_Data12- (MSB)
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
ExtTrgGrb (TTL)
Reserved
Reserved
Reserved
Reserved
Reserved
GND
GND
4