S9132 Datasheet, PDF (2/6 Pages) Hamamatsu Corporation – Profile sensor High-speed frame rate sensor capable of acquiring two-dimensional projection data

Profile sensor S9132
s Recommended terminal voltage
Parameter
Symbol
Min.
Typ.
Max.
Unit
Analog supply voltage
Vdd (A)
4.75
5
5.25
V
Digital supply voltage *²
Vdd (D)
3
5
Vdd (A)
V
Gain selection terminal High gain
voltage
Low gain
Vg
0
Vdd (A) -0.25
-
Vdd (A)
0.4
Vdd (A) +0.25
V
AD mode selection
voltage
10-bit MODE
8-bit MODE
Vsel
Vdd (A) -0.25
0
Vdd (A)
-
Vdd (A) +0.25
0.4
V
Clock pulse voltage
High level
Low level
V (CLK)
Vdd (D) -0.25
0
Vdd (D)
-
Vdd (D) +0.25
0.4
V
Start pulse voltage
High level
Low level
V (ST)
Vdd (D) -0.25
0
Vdd (D)
-
Vdd (D) +0.25
0.4
V
*2: When the latter-stage digital processing circuit is a 3.3 V family, the high level of digital output signal is 3.3 V when operated at
Vdd (A)=5 V, Vdd (D)=3.3 V.
s Electrical characteristics (Ta=25 °C)
Parameter
Symbol
Min.
Typ.
Clock pulse frequency *³
10-bit MODE
8-bit MODE
f (CLK)
500
500
-
-
Start pulse intervals
T (ST)
3101/f (CLK)
-
Video data rate
VR
-
f (CLK)/12
Digital output voltage
High level
Low level
VDO (H)
VDO (L)
Vdd (D)-0.15
-
-
-
Digital output rise time
(10 to 90 %)*⁴
CL=10 pF
CL=30 pF
tr
-
-
-
-
Digital output fall time
(10 to 90 %)*⁴
CL=10 pF
CL=30 pF
tf
-
-
-
-
Power consumption *⁵
P
-
75
*3: Vdd (A)=Vdd (D)=5 V, V (CLK)=V (ST)=5 V, Vg=5 V (Low gain)
*4: CL: Load capacitance of digital output terminal
*5: Vdd (A)=Vdd (D)=5 V, V (CLK)=V (ST)=V (ST)=5 V, f (CLK)=5 MHz, f (ST)=1.5 kHz
Max.
Unit
5M
10 M
Hz
-
s
-
Hz
-
0.15
V
30
60
ns
30
60
ns
-
mW
s Electrical and optical characteristics [Ta=25 °C, Vdd (A)=Vdd (D)=5 V, V (CLK)=V (ST)=5 V]
Parameter
Symbol
Min.
Typ.
Max.
Unit
Spectral response range
λ
380 to 1000
nm
Peak sensitivity wavelength
λp
-
500
-
nm
Photo sensitivity *⁶
High gain
RES
-
Low gain
-
40
8
-
-
V/nJ
Dark current
ID
-
0.2
0.6
pA
Saturation charge
Qsat
-
8
-
pC
Feedback capacitance
of charge amplifier *⁷
High gain
Low gain
Cf
-
-
0.2
1
-
-
pF
Dark output voltage *⁸
High gain
Vd
-
Low gain
-
100
20
300
60
mV
Saturation output
voltage
High gain
Low gain
Vsat
2.5
2.5
3.5
3
-
-
V
Photo response non-uniformity *⁹
PRNU
-
-
±10
%
*6: Vg=5 V (Low gain), Vg=0 V (High gain)
*7: λ=780 nm
*8: Storage time Ts=100 ms
*9: Uniformity is defined under the condition that the device is uniformly illuminated by light which is 50 % of the saturation
exposure level and using 254 pixels excluding both ends pixels as follows:
PRNU=∆V/V × 100 (%)
X: the average output of all pixels, ∆X: the difference from the maximum or minimum output and X
2