S11962-01CR_15 Datasheet, PDF (2/10 Pages) Hamamatsu Corporation – Distance area image sensor

Distance area image sensor
S11962-01CR
Recommended terminal voltage (Ta=25 °C)
Parameter
Symbol
Min.
Typ.
Max.
Unit
Analog supply voltage
Vdd(A)
4.75
5
5.25
V
Digital supply voltage
Vdd(D)
4.75
5
5.25
V
Pixel amplifier
Vsf
4.5
5
Vdd(A)
V
Bias voltage
Pixel reset
Vr
3.7
3.9
4.1
V
Output offset
Vref
2.3
2.5
2.7
V
Photosensitive area
Vpg
0.8
1.0
1.2
V
Frame reset pulse voltage
High level
Low level
reset
Vdd(D) × 0.8
-
-
-
-
Vdd(D) × 0.2
V
Frame synchronous trigger pulse High level
voltage
Low level
vst
Vdd(D) × 0.8
-
-
-
-
Vdd(D) × 0.2
V
Line synchronous trigger pulse High level
voltage
Low level
hst
Vdd(D) × 0.8
-
-
-
-
Vdd(D) × 0.2
V
Master clock pulse voltage
High level
Low level
mclk
Vdd(D) × 0.8
-
-
-
-
Vdd(D) × 0.2
V
Pixel reset pulse voltage
High level
Low level
ext_res
Vdd(D) × 0.8
-
-
-
-
Vdd(D) × 0.2
V
Output signal effective period High level
pulse voltage
Low level
oe
Vdd(D) × 0.8
-
-
-
-
Vdd(D) × 0.2
V
Output signal synchronous pulse High level
voltage
Low level
dclk
Vdd(D) × 0.8
-
-
-
-
Vdd(D) × 0.2
V
Non-readout period pulse voltage
High level
Low level
dis_read
Vdd(D) × 0.8
-
-
-
-
Vdd(D) × 0.2
V
Electrical characteristics [Ta=25 °C, Vdd(A)=Vdd(D)=5 V]
Parameter
Clock pulse frequency
Video data rate
Current consumption
Symbol
Condition
Min.
f(mclk)
1M
VR
-
Ic
Dark state
-
Typ.
-
f(mclk)
10
Max.
Unit
10 M
Hz
-
Hz
20
mA
Electrical and optical characteristics [Ta=25 °C, Vdd(A)=Vdd(D)=5 V, Vsf=5 V, Vr=4.25 V, MCLK=5 MHz]
Parameter
Symbol
Min.
Typ.
Max.
Unit
Spectral response range
λ
400 to 1100
nm
Peak sensitivity wavelength
λp
-
800
-
nm
Photosensitivity*³
Dark output
S
1.15 × 10¹²
Vd
-
2.3 × 10¹²
0.5
4.6 × 10¹²
10
V/W·s
V/s
Random noise
RN
-
0.8
1.6
mV rms
Dark output voltage*⁴
Vor
Vref + 1.0
-
Vref + 2.1
V
Saturation output voltage
Sensitivity ratio*⁵
Photoresponse nonuniformity*⁶
Vsat
SR
PRNU
Vref - 1.1
0.7
-
-
Vref + 0.3
V
-
1.43
-
-
±10
%
*3: Monochromatic wavelength source (λ=805 nm)
*4: Output voltage right after reset in dark state
*5: Sensitivity ratio of Vout1 (VTX1=3 V, VTX2=VTX3=0 V) to Vout2 (VTX2=3 V, VTX1=VTX3=0 V)
*6: Photoresponse nonuniformity (PRNU) is the output nonuniformity that occurs when the entire photosensitive area is uniformly
illuminated by white light which is approx. 50% of the saturation level. PRNU is measured using the pixels excluding the pixels of
the 4 outermost lines and defective pixels, and is defined as follows:
PRNU= ∆X/X × 100 (%)
X: average output of all pixels, ∆X: standard deviation of pixel output
2