GS7025 Datasheet, PDF (10/13 Pages) Gennum Corporation – Serial Digital Receiver

3. FREQUENCY ACQUISITION
The core PLL is able to lock if the incoming data rate and
the PLL clock frequency are within the PLL capture range
(which is slightly larger than the loop bandwidth). To assist
the PLL to lock, the GS7025 uses a frequency acquisition
circuit.
The frequency acquisition circuit sweeps the VCO control
voltage so that the VCO frequency changes from -10% to
+10% of the centre frequency. Figure 11 shows a typical
sweep waveform.
t_swp
t_sys
V_LF
A
T_cycle
T_cycle = t_swp + t_sys
Fig. 11 Typical Sweep Waveform
The VCO frequency starts at point A and sweeps up
attempting to lock. If lock is not established during the up
sweep, the VCO is then swept down. The system is
designed such that the probability of locking within one
cycle period is greater than 0.999. If the system does not
lock within one cycle period, it will attempt to lock in the
subsequent cycle.
The average sweep time, t_swp, is determined by the loop
filter component, C_LF1, and the charge pump current, Ι_CP:
t_SWP
=
4_----C_{-----L---F---1-}
3I_CP
The nominal sweep time is approximately 121µs when
C_LF1 = 15nF and Ι_CP = 165µA (R_VCO = 365Ω).
An internal system clock determines t_sys (see section 3-1,
Logic Circuit).
3-1. Logic Circuit
The GS7025 is controlled by a finite state logic circuit which
is clocked by an asynchronous system clock. That is, the
system clock is completely independent of the incoming
data rate. The system clock runs at low frequencies, relative
to the incoming data rate, and thus reduces interference to
the PLL.The period of the system clock is set by the C_OSC
capacitor and is:
t_sys = 9.6 × 10⁴ × C_OSC[ sec onds]
The recommended value for t_sys is 450µs (C_OSC = 4.7nF)
4. LOCKING
The GS7025 indicates valid lock when the following three
conditions are satisfied:
1. Input data is detected.
2. The incoming data signal and the PLL clock are phase
locked.
3. The system is not locked to an integer-multiple harmonic
of a 270Mb/s SMPTE 259M-C signal.
The GS7025 defines the presence of input data when at
least one data transition occurs every 1µs.
The GS7025 assumes that it is NOT locked to a harmonic if
the pattern ‘101’ or ‘010’ (in the reclocked data stream)
occurs at least once every t_sys/3 seconds. Using the
recommended component values, this corresponds to
approximately 150µs. In a harmonically locked system, all
bit cells are double clocked and the above patterns
become ‘110011’ and ‘001100’, respectively.
4-1. Lock Time
Synchronous switching refers to the case where the input
data is changed from one source to another source which is
at the same data rate (but different phase).
When input data to the GS7025 is removed, the GS7025
latches the current state. Therefore, when data is reapplied,
the GS7025 begins the lock procedure at the previous
locked data rate. As a result, in synchronous switching
applications, the GS7025 locks very quickly. The nominal
lock time depends on the switching time and is summarized
in the Table 3.
TABLE 3.
SWITCHING TIME
<0.5µs
0.5µs - 10ms
>10ms
LOCK TIME
10µs
2t_sys
2T_cycle + 2t_sys
To acquire lock, the frequency acquisition circuit may have
to sweep over an entire cycle depending on initial
conditions. Maximum lock time is 2T_cycle + 2t_sys.
The nominal value of T_cycle for the GS7025 operating in a
typical SMPTE 259M-C application is approximately 1.3ms.
The GS7025 has a dedicated LOCK output (pin 39)
indicating when the device is locked. It should be noted
that in synchronous switching applications where the
switching time is less than 0.5µs, the LOCK output will NOT
be de-asserted and the data outputs will NOT be muted.
10
GENNUM CORPORATION
522 - 80 - 00