XR16V2652 Datasheet, PDF (7/48 Pages) Exar Corporation – HIGH PERFORMANCE DUART WITH 32-BYTE FIFO

REV. P1.0.0
2.0 FUNCTIONAL DESCRIPTIONS
2.1 CPU Interface
PRELIMINARY
XR16V2652
HIGH PERFORMANCE DUART WITH 32-BYTE FIFO
The CPU interface is 8 data bits wide with 3 address lines and control signals to execute data bus read and
write transactions. The V2652 data interface supports the Intel compatible types of CPUs and it is compatible
to the industry standard 16C550 UART. No clock (oscillator nor external clock) is required to operate a data
bus transaction. Each bus cycle is asynchronous using CS#, IOR# and IOW# signals. Both UART channels
share the same data bus for host operations. The data bus interconnections are shown in Figure 3
FIGURE 3. XR16V2652 DATA BUS INTERCONNECTIONS
D0
D1
D2
D3
D4
D5
D6
D7
A0
A1
A2
IOR#
IOW#
UART_CS#
UART_CHSEL
UART_INTA
UART_INTB
TXRDYA#
(RXRDYA#)
TXRDYB#
(RXRDYB#)
UART_RESET
D0
D1
D2
D3
D4
D5
D6
D7
A0
A1
A2
IOR#
IOW#
VCC
TXA
RXA
DTRA#
RTSA#
UART
Channel A
CTSA#
DSRA#
CDA#
RIA#
(O P2A #)
(BAUDOUTA#)
CS#
CHSEL
INTA
INTB
TXRDYA#
(RXRDYA#)
TXRDYB#
(RXRDYB#)
TXB
RXB
DTRB#
UART ^RTSB#
Channel B CTSB#
DSRB#
CDB#
RIB#
(O P2B #)
(BAUDOUTB#)
RESET
GND
VCC
Serial Interface of
RS-232, RS-422
Serial Interface of
RS-232, RS-422
Pins in parentheses become available through the MF# pin. MF# A/B becomes RXRDY# A/B when AFR[2:1] = '10'. MF# A/B becomes OP2# A/B
when AFR[2:1] = '00'. MF# A/B becomes BAUDOUT# A/B when AFR[1:0] = '01'.
2.2 5-Volt Tolerant Inputs
The V2652 can accept up to 5V inputs even when operating at 3.3V or 2.5V. But note that if the V2652 is
operating at 2.5V, its V_OH may not be high enough to meet the requirements of the V_IH of a CPU or a serial
transceiver that is operating at 5V.
2.3 Device Reset
The RESET input resets the internal registers and the serial interface outputs in both channels to their default
state (see Table 15). An active high pulse of longer than 40 ns duration will be required to activate the reset
function in the device.
2.4 Device Identification and Revision
The XR16V2652 provides a Device Identification code and a Device Revision code to distinguish the part from
other devices and revisions. To read the identification code from the part, it is required to set the baud rate
generator registers DLL and DLM both to 0x00 (DLD = 0xXX). Now reading the content of the DLM will provide
0x06 for the XR16V2652 and reading the content of DLL will provide the revision of the part; for example, a
reading of 0x01 means revision A.
2.5 Channel A and B Selection
The UART provides the user with the capability to bi-directionally transfer information between an external
CPU and an external serial communication device. A logic 0 on chip select pin (CS#) allows the user to select
the UART and then using the channel select (CHSEL) pin, the user can select channel A or B to configure,
send transmit data and/or unload receive data to/from the UART. Individual channel select functions are shown
in Table 1.
7