SEP04G72G1AH2MT-30R Datasheet, PDF (7/16 Pages) List of Unclassifed Manufacturers – 4GB DDR2 . SDRAM registered DIMM

Data Sheet
Rev.1.2 14.02.2014
I_DD Specifications and Conditions
(0°C ≤ TCASE ≤ + 85°C ; VDDQ = +1.8V ± 0.1V, VDD = +1.8V ± 0.1V)
Parameter
& Test Condition
OPERATING CURRENT *) :
One device bank Active-Precharge;
t_RC= t_RC (I_DD); t_CK = t_CK (I_DD); CKE is HIGH, CS# is HIGH
between valid commands;
DQ inputs changing once per clock cycle; Address and control
inputs changing once every two clock cycles
OPERATING CURRENT :*)
One device bank; Active-Read-Precharge;
I_OUT = 0mA; BL = 4, CL = CL (I_DD), AL = 0;
t_CK = t_CK (I_DD), t_RC= t_RC (I_DD), t_RAS = t_RAS MIN (I_DD),
t_RCD = t_RCD (I_DD); CKE is HIGH, CS# is HIGH between valid
commands; Address inputs changing once every two clock
cycles; Data Pattern is same as I_DD4W
PRECHARGE POWER-DOWN CURRENT:
All device banks idle; Power-down mode;
t_CK = t_CK (I_DD); CKE is LOW; All Control and Address bus inputs
are not changing; DQ’s are floating at V_REF
PRECHARGE QUIET STANDBY CURRENT:
All device banks idle;
t_CK = t_CK (I_DD); CKE is HIGH, CS# is HIGH;
All Control and Address bus inputs are not changing; DQ’s are
floating at V_REF
PRECHARGE STANDBY CURRENT:
All device banks idle;
t_CK = t_CK (I_DD); CKE is HIGH, CS# is HIGH;
All other Control and Address bus inputs are changing once
every two clock cycles; DQ inputs changing once per clock
cycle
ACTIVE POWER-DOWN
CURRENT:
Fast PDN Exit
MR[12] = 0
All device banks open; t_CK = t_CK
(I_DD); CKE is LOW; All Control and
Slow PDN Exit
MR[12] = 1
Address bus inputs are not
changing; DQ’s are floating at
V_REF
ACTIVE STANDBY CURRENT:
All device banks open; t_CK = t_CK (I_DD),
t_RAS = t_RAS MAX (I_DD), t_RP = t_RP (I_DD);
CKE is HIGH, CS# is HIGH between valid commands;
All other Control and Address bus inputs are changing once
every two clock cycles; DQ inputs changing once per clock
cycle
OPERATING READ CURRENT:
All device banks open, Continuous burst reads; One module
rank active; I_OUT = 0mA; BL = 4, CL = CL (I_DD), AL = 0; t_CK = t_CK
(I_DD), t_RAS = t_RAS MAX (I_DD), t_RP = t_RP (I_DD); CKE is HIGH, CS# is
HIGH between valid commands; Address bus inputs are
changing once every two clock cycles; DQ inputs changing
once per clock cycle
Symbol
I_DD0
max.
6400-CL6 5300-CL5
1296
1206
Unit
mA
I_DD1
1476
1386 mA
I_DD2P
252
252
mA
I_DD2Q
864
864
mA
I_DD2N
1008
864
mA
I_DD3P
720
540
mA
360
360
I_DD3N
1188
1080 mA
I_DD4R
2286
2106 mA
Swissbit AG
Industriestrasse 4
CH-9552 Bronschhofen
Fon: [phone]
Fax: [phone]
www.swissbit.com
eMail: [e-mail]
Page 7
of 16