10409 Datasheet, PDF (3/7 Pages) List of Unclassifed Manufacturers – Statguard Conductive Acrylic Paint Application Instructions

1.
2.
Figure 4. Electrical testing on
the painted floor using a Surface
Resistance Test Kit.
Use a razor to cut into a painted, dried
floor.
3.
Apply tape on the precut area.
4.
maintenance. Apply Statguard^® Floor Finish
after 48-72 hours after last coat of paint. Paint
becomes dry to the touch, but is not fully cured
to accept a finish coat until this time. If you
notice the paint color coming off when finishing,
it is too soon to apply. Please wait for the
paint to cure fully. Ask for Technical Bulletin
TB-2088 for more information on Statguard^®
Floor Finish.
Pull the tape off.
Examine the degree of paint separation
from the concrete.
Physical Properties
Figure 5. Adhesion test on the painted floor.
Type:
  Water base acrylic coating
Color:
  Grey, Light Grey
Vehicle Type:
  Pure acrylic resin waterborne
  10E5 ohms/sq. per ASTM D257
Static Charge Decay:
  <0.01 sec. per FTMS 101B, Method 4046
Charge Generation:
  Zero per AATCC Step Test, Method 134-1979
RTT:
  10E5 ohms per ANSI ESD-S7.1
Pigment Type:
  Lead free, iron oxide, titanium dioxide and extenders
RTG:
  10E5 ohms per ANSI ESD-S7.1
Viscosity:
  Light Grey
  Grey
26” #3 Zahn cup
23” #3 Zahn cup
Solids:
  Light Grey
  Grey
24% by volume
20% by volume
Coating Density:
  Light Grey
9.54 lbs per gallon
  Grey
10.27 lbs per gallon (1.0 kilograms per
litre)
Gloss:
  Light Grey
  Grey
2 @ 60°F
22 @ 60°F (30 @ 60°C)
Temperature Range:
Wet: 33°F - 110°F (1°C - 43°C)
Dry: 33°F - 300°F (1°C - 149°C)
    (300°F [149°C] not continuous)
Electrical Properties
Surface Resistivity:
Testing
Test patch areas should be tested for adhesion and electrical
performance of the paint before applying paint to the entire floor. To
best ensure consistent results, the test should be done at various
locations.
ELECTRICAL PROPERTIES:
Test the surface resistivity, point-to-point resistance, and resistance-
to-ground properties of coated area per ANSI ESD-S7.1 test method.
For quick and easy verification of the paint’s electrical properties,
we recommend the use of our a Surface Resistance Test Kit (Figure
4). For more information contact any of the Desco Industries Inc.
companies.
ADHESION:
Allow newly applied paint to dry a minimum of 48 hours before
proceeding with the test. At humidity levels over 55% RH, allow 72
hours of drying time before testing. Use a razor to cut a cross or a few
perpendicular lines over a 3” by 3” (75 mm by 75 mm) area on several
spots of the thoroughly dried area. Use a piece of masking tape to
cover the marked area. Make sure the tape is thoroughly adhered to
the test area. Pull the tape off the surface and examine the amount
of paint which has peeled off during the test. If any significant portion
is transferred to the tape, better surface preparation (acid etching,
cleaning or sanding) should be done on the substrate to enhance the
adhesion.
DESCO INDUSTRIES INC. • 3651 Walnut Avenue, Chino, CA 91710 • [phone] • Fax [phone] • Web Site: DescoIndustries.com
TB-7001 Page 3 of 7
© 2011 DESCO INDUSTRIES INC.
Employee Owned