WC-260 Datasheet, PDF (2/8 Pages) List of Unclassifed Manufacturers – Crimping tools and machines

Hand tools
Crimping tools
for chain terminals
YRS
series
YC
series
Hand tools
for loose piece terminals
YRM
series
YRF
series
YRK
series
YRK-EX
series
Terminals and parts model
number in alphabetical order
Dimensions:
(W×L) 59×224mm
Dimensions:
(W×L) 70×296mm
Dimensions:
(W×L) 59×224mm
Dimensions:
(W×L) 70×295mm
80×305mm
Dimensions:
(W×L×D)
75×314×25mm
Crimping tools
It is the manual tool that is convenience to terminate very small quantity of contacts for prototype or maintenance.
It is composed of two crimping dies for the conductor and insulation, and can be crimp easily.
YRK and YRK-EX can be used for mass-production.
Dimensions:
(W×L×D)
75×314×25mm
Note: (1) These tools are for prototype tooling or repair.
(2) YC tool has two crimping sections (A and B). YRS tool has also two crimping sections by inverting upper dies.
Be sure to check applicable wires before use. Since the dies are fixed, the crimping height cannot be adjusted. Therefore, some of the
applicable wires described in this catalog may not be crimped properly.
Before use, check for proper crimping (such as tensile strength, terminal/contact deformation).
(3) These tools are not applicable to 2-wire crimping.
(4) When hand crimping board-in terminals (SAN, SCN, SDN, SGN, SIN, SJN, SZN), care should be taken not to contaminate the solder tails of
the terminals, as with greasy or oily fingers. If a solder problem arises, some cleaning of the tips of the terminal is advisable.
(5) WC and JUC hand tools are provided by J.S.T.(U.K.) LTD. and contact them about the details of these hand tools.
YRS series
YC series
YRM series
YRF series
YRK ^. YRK-EX series
JK-SP/SS2***
YRS-370
–
–
–
–
J-SP/SS1***
YRS-440
YC-440
–
–
–
J-SP/SS2***
YRS-330
–
–
–
–
LFO-1.0-250N
–
–
–
–
–
LFO-2.5-250N
–
–
–
–
–
MD-SP12**
YRS-470
–
–
–
–
MD-SP22**
YRS-460
–
–
–
–
RA-SC1290
YRS-231
YRM-232
–
YRM-233
–
–
RF-SC22**
–
–
YRM-230
–
–
RPJ-SP/SS2331
YRS-331
–
–
–
–
SAA-21(T)-**
–
YC-141
–
–
–
SAA-50(T)-**
–
YC-182
–
–
–
SAA-51(T)-**
–
YC-142
–
–
–
SAB-51(T)-**
–
YC-142
–
–
–
SACH-003G-P0.2
YRS-1190
–
–
–
–
SACH-002GU-P0.3
YRS-858
–
–
–
–
SAN-002T-0.8A
SAN-002T-0.8K
YRS-220
–
–
–
–
SBH-001T-P0.5
–
YC-670R
–
–
–
SBHL-002T-P0.5
YRS-857
–
–
–
–
SBHM-001T-P0.5
–
YC-670R
–
–
–
SBHS-002T-P0.5A
YRS-852
–
–
–
–
SBHS-002T-P0.5A
–
–
–
–
–
SBHSM-002T-P0.5
YRS-854
–
–
–
–
SBHT-002T-P0.5
YRS-856
YRS-857
–
–
–
–
SBN-001T-1.0
YRS-170
YC-170R
–
–
–
–
SCN-001T-1.0K
YRS-191
YC-191R
–
–
–
SCN-001T-P1.0
SCS-41T-2.3
–
–
–
–
–
SCSN-41T-P2.3
–
–
–
–
–
SCZH-002T-P0.5
YRS-492
–
–
–
–
Note: Contact JST for wire range.
3
Hand tools
for loose piece terminals
Crimping tools
Extraction and Insertion tools
Extraction tool
Insertion tool
Extraction tool is used to extract
contacts improperly inserted in the housing.
Insertion tool allows contacts be inserted
in the housing.
This tool greatly increases efficiency especially
when thin wires are used.
WC & JUC series
JUK's Hand Tools
–
–
–
JUCS-FO
JUCS-FO
–
–
–
–
–
–
–
–
–
–
–
–
WC-670
–
–
–
–
–
–
–
WC-191
–
–
–
Terminal in loose form
model No.
–
J-BP/BS1***
–
–
–
–
–
RA-BC12**
RF-BC22**
–
LAA-21(T-)**
LAA-50(T)-**
LAA-51(T)-**
LAB-51(T)-**
–
–
–
BBH-001T-P0.5
–
BBHM-001T-P0.5
–
–
–
–
BBN-001T-1.0
BCN-001T-1.0K
BCN-001T-P1.0
–
–
–
KEJ-0.7 for plug, KEJ-0.4 for socket
DEJ-0.3
DEJ-0.3
–
–
MEJ-06
MEJ-06
EJ-RA
–
EJ-RPJ
–
–
–
–
–
–
EJ-PH
–
–
EJ-BHMR
EJ-BHS2
EJ-BHS2
EJ-BHSW
EJ-BHT
–
–
CSJ-23
EJ-CSN
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
4