ATV32H055N4 Datasheet, PDF (2/10 Pages) List of Unclassifed Manufacturers – variable speed drive ATV32

Noise level
Insulation
Electrical connection
Tightening torque
Supply
Analogue input number
Analogue input type
Sampling duration
Response time
Accuracy
Linearity error
Analogue output number
Analogue output type
Discrete output number
Discrete output type
Minimum switching current
Maximum switching current
Discrete input number
Discrete input type
Discrete input logic
Acceleration and deceleration ramps
Braking to standstill
Protection type
Communication port protocol
Type of connector
Physical interface
Transmission frame
Type of polarization
2
43 dB 86/188/EEC
Electrical between power and control
Screw terminal 1.5...4 mm² AWG 14...AWG 10 power supply
Removable screw terminals 1.5...2.5 mm² AWG 14...AWG 12 motor/braking re-
sistor
Screw terminal 0.5...1.5 mm² AWG 18...AWG 14 control
0.6 N.m 5.3 lb/ft power supply
0.7 N.m 7.1 lb/ft motor/braking resistor
0.5 N.m 4.4 lb/ft control
Internal supply for reference potentiometer (1 to 10 kOhm) 10.5 V DC +/- 5 % <=
10 mA overload and short-circuit protection
3
Current AI3 0...20 mA (or 4-20 mA, x-20 mA, 20-x mA or other patterns by config-
uration) 250 Ohm 10 bits
Bipolar differential voltage AI2 +/- 10 V DC 30000 Ohm 10 bits
Voltage AI1 0...10 V DC 30000 Ohm 10 bits
2 ms AO1 analog
2 ms AI1, AI2, AI3 analog
2 ms R2A, R2C relay
2 ms R1A, R1B, R1C relay
8 ms +/- 0.7 ms LI1...LI6 logic
+/- 2 % AO1 for a temperature of -10...60 °C
+/- 1 % AO1 for a temperature of 25 °C
+/- 0.5 % AI1, AI2, AI3 for a temperature of 25 °C
+/- 0.2 % AI1, AI2, AI3 for a temperature of -10...60 °C
+/- 0.3 % AO1
+/- 0.2...0.5 % of maximum value AI1, AI2, AI3
1
Software-configurable voltage AO1 0...10 V 470 Ohm 10 bits
Software-configurable current AO1 0...20 mA 800 Ohm 10 bits
3
Logic LO
Configurable relay logic R2A, R2B NO 100000 cycles
Configurable relay logic R1A, R1B, R1C NO/NC 100000 cycles
5 mA 24 V DC configurable relay logic
5 A 30 V DC resistive cos phi = 1 R2
5 A 250 V AC resistive cos phi = 1 R2
2 A 30 V DC inductive cos phi = 0.4 R1, R2
2 A 250 V AC inductive cos phi = 0.4 R1, R2
4 A 30 V DC resistive cos phi = 1 R1
3 A 250 V AC resistive cos phi = 1 R1
7
Safe torque off STO 24...30 V DC 1500 Ohm
Switch-configurable PTC probe LI6 24...30 V DC
Programmable as pulse input 20 kpps LI5 24...30 V DC level 1 PLC
Programmable (sink/source) LI1...LI4 24...30 V DC level 1 PLC
Positive logic (source) LI1...LI6 < 5 V > 11 V
Negative logic (sink) LI1...LI6 > 19 V < 13 V
S
U
CUS
Deceleration ramp automatic stop DC injection
Deceleration ramp adaptation
Linear
Ramp switching
By DC injection
Thermal protection drive
Short-circuit between motor phases drive
Overheating protection drive
Overcurrent between output phases and earth drive
Input phase breaks drive
CANopen
Modbus
1 RJ45 Modbus/CANopen on front face
2-wire RS 485 Modbus
RTU Modbus
No impedance Modbus