NRF2401A Datasheet, PDF (4/38 Pages) List of Unclassifed Manufacturers – Single chip 2.4 GHz Transceiver

PRODUCT SPECIFICATION
nRF2401A Single Chip 2.4 GHz Radio Transceiver
ELECTRICAL SPECIFICATIONS
Conditions: VDD = +3V, VSS = 0V, T_A = - 40ºC to + 85ºC
Symbol Parameter (condition)
Notes Min.
Typ. Max. Units
VDD
TEMP
Operating conditions
Supply voltage
Operating Temperature
1.9
3.0
3.6
-40
+27
+85
Digital input pin
V_IH HIGH level input voltage
V_IL LOW level input voltage
VDD- 0.3
Vss
VDD
0.3
Digital output pin
V_OH HIGH level output voltage (I_OH=-0.5mA)
V_OL LOW level output voltage (I_OL=0.5mA)
VDD- 0.3
Vss
VDD
0.3
f_OP
f_XTAL
∆f
R_GFSK
R_GFSK
F_CHANNEL
General RF conditions
Operating frequency
Crystal frequency
Frequency deviation
Data rate ShockBurst™
Data rate Direct Mode
Channel spacing
1)
2400
2524
2)
4
20
±156
>0
1000
3)
250
1000
1
Transmitter operation
P_RF Maximum Output Power
4)
0
+4
P_RFC RF Power Control Range
16
20
P_RFCR RF Power Control Range Resolution
±3
P_BW 20dB Bandwidth for Modulated Carrier
P_RF2 2^nd Adjacent Channel Transmit Power 2MHz
P_RF3 3^rd Adjacent Channel Transmit Power 3MHz
1000
-20
-40
I_VDD Supply current @ 0dBm output power
5)
13
I_VDD Supply current @ -20dBm output power
5)
8.8
I_VDD Average Supply current @ -5dBm output
6)
0.8
power, ShockBurst™
I_VDD Average Supply current in stand-by mode
7)
12
I_VDD Average Supply current in power down
400
Receiver operation
I_VDD Supply current one channel 250kbps
18
I_VDD Supply current one channel 1000kbps
19
I_VDD Supply current two channels 250kbps
23
I_VDD Supply current two channels 1000kbps
25
RX_SENS Sensitivity at 0.1%BER (@250kbps)
-93
RX_SENS Sensitivity at 0.1%BER (@1000kbps)
-85
C/I_CO C/I Co-channel
8)
C/I_1ST 1^st Adjacent Channel Selectivity C/I 1MHz
8)
C/I_2ND 2^nd Adjacent Channel Selectivity C/I 2MHz
8)
C/I_3RD 3^rd Adjacent Channel Selectivity C/I 3MHz
8)
10/4
-20/0
-37/-20
-43/-30
RX_B Blocking Data Channel 2
-45/-41
1) Usable band is determined by local regulations
2) The crystal frequency may be chosen from 5 different values (4, 8, 12, 16, and 20MHz) which are specified in the
configuration word, see Table 8. 16MHz are required for 1Mbps operation.
3) Data rate must be either 250kbps or 1000kbps.
4) Antenna load impedance = 100Ω+j175Ω
5) Antenna load impedance = 100Ω+j175Ω. Effective data rate 250kbps or 1Mbps.
6) Antenna load impedance = 100Ω+j175Ω. Effective data rate 10kbps.
7) Current if 4 MHz crystal is used.
8) 250kbps/1000kbps.
Table 4 nRF2401A RF specifications
V
ºC
V
V
V
V
MHz
MHz
kHz
kbps
kbps
MHz
dBm
dB
dB
kHz
dBm
dBm
mA
mA
mA
µA
nA
mA
mA
mA
mA
dBm
dBm
dB
dB
dB
dB
dB
Nordic Semiconductor ASA - Vestre Rosten 81, N-7075 Tiller, Norway - Phone [phone] - Fax [phone]
Revision: 1.0
Page 4 of 38
December 2004