A1042 Datasheet, PDF (23/24 Pages) List of Unclassifed Manufacturers – Desoldering Tool

8. Specifications
Model No.
Power Consumption
70W
HAKKO 475
Part Name
Output Voltage
AC 24V
Vacuum Generator
Ejector type
Vacuum Pressure (max.)
93kPa (700 mm Hg) (28 in. Hg)
Suction Flow
20 l/min.*
Nozzle to Ground Potential < 2mV
Nozzle to Ground Resistance < 2Ω
Applied Air Pressure
490kPa (5.0kgf/cm²)
Compressed Air Consumption 1.62 c.f.m. (46l/min.)
Dimensions
165(W) × 135(H) × 260(D)mm
(6.50 × 5.31 × 10.24 in.)
Weight (w/o cord)
3.0kg (6.6lb.)
*This suction flow is measured at the filter case suction port of Station.
Desoldering Gun
Model No.
Part No.
Power Consumption
Temperature Range
Insulation Resistance
Nozzle Inside Diameter
Dimensions
Weight (w/o cord)
HAKKO 809
C1183
AC 24V / 50W
380 to 480°C (716 to 896°F)
> 300MΩ at 420°C (790°F)
ø1.0mm (0.04 in.) (nozzle S standard)
135(W) × 174(H)mm (5.31 × 6.85 in.)
200g (0.44lb.)
Condition of measurement
• Insulation resistance
The insulation resistance was measured between the nozzle and the lead of
the heating element using a 500 V DC insulation resistance meter.
Caution: The insulation resistance cannot be measured between the nozzle
and the power plug as the transformer between the secondary part (heating
element) and the primary part acts as an insulator.
• Voltage leakage
The voltage leakage was measured between the nozzle and the grounding
plug at a temperature of 480°C (896°F) using an AC mV meter.
Caution: Be sure to ground the unit before measuring the voltage leakage.
• Specifications and design are subject to change without notice.
9. Wiring
P.W.B.
Replacement Parts
Part No.
Part Name
A1002 Nozzle S ø0.8mm (0.03 in.)
A1003 Nozzle S ø1.0mm (0.04 in.)
A1004 Nozzle ø0.8mm (0.03 in.)
A1005 Nozzle ø1.0mm (0.04 in.)
A1006 Nozzle ø1.3mm (0.05 in.)
A1007 Nozzle ø1.6mm (0.06 in.)
Specifications
Part No.
øA
øB
A1002 0.8mm (0.03 in.) 1.8mm (0.07 in.)
A1003 1.0mm (0.04 in.) 2.0mm (0.08 in.)
Part No.
øA
A1004 0.8mm (0.03 in.)
A1005 1.0mm (0.04 in.)
A1006 1.3mm (0.05 in.)
A1007 1.6mm (0.06in.)
øB
2.3mm (0.09 in.)
2.5mm (0.1 in.)
3.0mm (0.12 in.)
3.0mm (0.12 in.)
Part No.
B1215
B1086
B1087
B1088
B1089
B1302
B1303
B1304
B1305
Part Name
Cleaning pin
Cleaning pin
Cleaning pin
Cleaning pin
Cleaning pin
Cleaning drill
Cleaning drill
Cleaning drill
Cleaning drill
Specifications
for heating element
for ø0.8mm (0.03 in.) nozzle
for ø1.0mm (0.04 in.) nozzle
for ø1.3mm (0.05 in.) nozzle
for ø1.6mm (0.06 in.) nozzle
for ø0.8mm (0.03 in.) nozzle
for ø1.0mm (0.04 in.) nozzle
for ø1.3mm (0.05 in.) nozzle
for ø1.6mm (0.06 in.) nozzle
Part No.
B2073
A1009
A1033
A1030
A1313
A1028
A1042
Part Name
Filter pipe
Ceramic paper filter (S)
Ceramic paper filter (L)
Spring filter
Heating element
Silicone grease
Cleaning sponge
Specifications
w/front holder & filters
for filter case 10pcs.
for filter pipe 10pcs
10pcs.
24V, 50W

H2 _TRANS ^H1
M2
TRANS
M1 TR
2
1
1
4
2
1
Solenoid Valve
2
3
Receptacle
Fuse Holder
Black
24V
White
Transformer
4
Power Switch
4
1
1
Power Cord
22