|
FX623 Datasheet, PDF (5/6 Pages) List of Unclassifed Manufacturers – Call Progress Tone Decoder | |||
|
◁ |
Specification
Absolute Maximum Ratings
Exceeding the maximum rating can result in device damage. Operation of the device outside the operating limits
is not implied.
Supply voltage
-0.3 to 7.0V
Input voltage at any pin (ref VSS = 0V)
-0.3 to (VDD + 0.3V)
Sink/source current (supply pins)
+/- 30mA
(other pins)
+/- 20mA
Total device dissipation @ TAMB 25°C
Derating
Storage temperature range: FX623P
800mW Max.
10mW/°C
-40°C to +85°C (plastic)
Operating Limits ......
Min. Max. Unit
Supply Voltage (V )
DD
Operating Temperature ......
3.0
5.5
-40
+85
V
at 25°C
°C
All device characteristics are measured under the following conditions unless otherwise specified:
VDD = 3.3V, TOP = -40 to +85 °C. Audio Level 0dB ref: = 775mVrms. Xtal/Clock Frequency = 3.579545MHz
Characteristics
See Note
Min.
Typ.
Max.
Unit
Static Values
Supply Current
Input Logic â1â
Input Logic â0â
Output Logic â1â
Output Logic â0â
Impedance
CS and PURS Input
Hold Input
1
Signal Input
IRQ Output (logic â1â)
IRQ Output (logic â0â)
Q0 - Q3 & Data-Change Outputs (logic â1â)
Q0 - Q3 & Data-Change Outputs (logic â0â)
Q0 - Q3 & Data-Change Outputs (high Z)
Dynamic Values
Signal Input Range
2, 5
Decode Bandedge Tolerance
3
Xtal Inverter
Voltage Gain
Input Impedance
Output Impedance
Decoder Timing - Figures 3 and 4
Power Up Reset Time
tPURS
Data 'E' Time
t
DE
NOTONE to Tone Response Time
tRESP
4
Tone to NOTONE Response Time tNT
4
Data to Data-Change Pulse Time t
DC
Data-Change Pulse Width
tPUL
Hold to Data-Change Rise Time tHOLD
HOLD to Data-Change Fall Time tNORM
IRQ Tone Response Time
tRIRQ
IRQ Reset Time
t
IR
Data Access Time
tACS
CS High to Output Tri-State Time t
HIZ
-
0.7
-
0.8
-
10.0
0.5
0.1
-
-
-
-
1.0
0.6
-
-
-
-
-
-
-
30.0
175
0.7
175
-
1.0
mA
-
%VDD
0.3
%VDD
-
%VDD
0.2
%VDD
-
Mâ¦
-
Mâ¦
-
Mâ¦
100
kâ¦
500
â¦
2.0
kâ¦
500
â¦
-
Mâ¦
35.0
1,166
mVrms
-1.0
-
1.0
%
20.0
-
-
V/V
10.0
-
-
Mâ¦
-
-
160
kâ¦
2.5
-
-
ms
31.0
-
-
ms
-
27.0
50.0
ms
-
-
60.0
ms
0.625
-
1.15
ms
-
1.25
-
ms
63.0
-
-
µs
-
-
150
µs
-
29.0
52.0
ms
-
-
250
ns
-
-
250
ns
-
-
100
ns
Notes
1. This pin has an on-chip 1.0M⦠pullup resistor.
2. An a.c. coupled sine or squarewave.
3. See Table 1, Tone Decode Frequencies.
4. Delay between the change of input (Tone/NOTONE) and the change at the Q0 - Q3 outputs.
5. The signal input maximum value is determined by the formula VDD/2.83.
5
|
▷ |