UHP-3-3-30-D48 Datasheet, PDF (3/4 Pages) List of Unclassifed Manufacturers – Single Output UHP Models

3.3V @ 30A, SINGLE OUTPUT CONVERTERS
UHP Models
Performance/Functional Specifications
Typical @ TA = +25°C under nominal line voltage, full-load conditions, unless noted. ➀
Input
Input Voltage Range
36-75 Volts (48V nominal)
Overvoltage Shutdown
77-81 Volts (79V typical)
Start-Up Threshold
34-36 Volts (35V typical)
Undervoltage Shutdown
32.5-34.5 Volts (33.5V typical)
Input Current:
Normal Operating Conditions
Standby Mode:
Off, OV, UV, Thermal Shutdown
See Ordering Guide
TBD typical
Input Reflected Ripple Current:
Source Impedance
<0.1Ω, no external input filtering
TBD
Internal Input Filter Type
Pi (0.01µF - TBDµH - 3.3µF)
Reverse-Polarity Protection
1 minute duration, 5A maximum
On/Off Control (Pin 3): ➂ ➃ ➅
"N" Suffix Models
On = open or 2.5V to +VIN,
IIN = less than 50µA
Off = 0-0.8V, IIN = 200µA @ 0V
On = 0-0.8V, IIN = TBD @ 0V
Off = open or TBD Volts
Sync (Option, Pin 6): ➂ ➃ ➅
Input Threshold
Input Voltage Low
Input Voltage High
Input Resistance
Output High Voltage (100µA load)
Output Drive Current
Input/Output Pulse Width
TBD Volts
TBD Volts
TBD Volts
TBD minimum
TBD Volts
TBD
TBD nsec
Output
VOUT Accuracy:
3.3V Output
±1.0% maximum
Minimum Loading Per Specification No load
Ripple/Noise (20MHz BW) ➄
See Ordering Guide
Line/Load Regulation
See Ordering Guide
Efficiency
See Ordering Guide
Output Voltage Sense Range
+10%
Trim Range ➁
±10%, –20%
Isolation Voltage:
Input-to-Output
1500Vdc minimum
Isolation Resistance
100MΩ
Isolation Capacitance
940pF
Current Limit Inception:
3.3V @ 98.5% VOUT
33-35 Amps
Short Circuit Current:
3.3V Output
TBD Amps average current
Overvoltage Protection:
3.3V Output
Comparator, latching
TBD Volts
Maximum Capacitive Loading
TBD µF
Temperature Coefficient
±0.02% per °C
Dynamic Characteristics
Dynamic Load Response:
3.3V (50-100% load step to 1% VOUT) TBDµsec maximum
Start-Up Time:
VIN to VOUT
TBD
On/Off to VOUT
TBD
Switching Frequency
350kHz (±35kHz)
DynaEnvironmental
MTBF ➆
Bellcore, ground fixed, full power
25°C ambient
TBD million hours
Operating Temperature (Ambient): ➁
Without Derating (200lfm)
With Derating
+52°C
To +100°C (See Derating Curves)
Thermal Shutdown
TBD
Storage Temperature
–40 to +120°C
Physical
Dimensions
2.3" x 2.4" x 0.465" (58.4 x 61 x 11.8mm)
Pin Material
Brass, solder coated
Weight:
2.24 ounces (63.5 grams)
Primary to Secondary Insulation Level Operational
➀ All models are specified with external 10µF tantalum and 1µF ceramic output capacitors.
➁ See Technical Notes/Graphs for details.
➂ The On/Off Control function can be replaced with a Sync function. See Part Number
Suffixes and Technical Notes for details.
➃ Applying a voltage to On/Off Control (pin 3) when no input power is applied to the
converter can cause permanent damage.
➄ Output noise may be further reduced with the installation of additional external output
capacitors. See Technical Notes.
➅ On/Off control is designed to be driven with open collector or by appropriate voltage
levels. Voltages must be referenced to the –Input (pin 1).
➆ Demonstrated MTBF available on request.
Absolute Maximum Ratings
Input Voltage:
Continuous:
Transient (100msec):
81 Volts
100 Volts
Input Reverse-Polarity Protection
Input Current must be <5A. 1 minute
duration. Fusing recommended.
Output Current
Current limited. Devices can withstand
an indefinite output short circuit.
On/Off Control (Pin 3) Max. Voltages
Referenced to –Input (pin 1)
+VIN
Storage Temperature
–40 to +120°C
Lead Temperature (Soldering, 10 sec.) +300°C
These are stress ratings. Exposure of devices to any of these conditions may adversely
affect long-term reliability. Proper operation under conditions other than those listed in the
Performance/Functional Specifications Table is not implied, nor recommended.
3