TMC93LC46 Datasheet, PDF (2/15 Pages) List of Unclassifed Manufacturers – 1K/2K/2K/4K/16K-Bit Microwire Serial EEPROM

93LC46/56/57/66/86
ABSOLUTE MAXIMUM RATINGS*
Temperature Under Bias .................. -55°C to +125°C
Storage Temperature ........................ -65°C to +150°C
Voltage on any Pin with
Respect to Ground⁽¹⁾ ............. -2.0V to +VCC +2.0V
V_CC with Respect to Ground ................ -2.0V to +7.0V
Package Power Dissipation
Capability (T_A = 25°C) ................................... 1.0W
Lead Soldering Temperature (10 secs) ............ 300°C
Output Short Circuit Current⁽²⁾ ........................ 100 mA
*COMMENT
Stresses above those listed under “Absolute Maximum
Ratings” may cause permanent damage to the device.
These are stress ratings only, and functional operation of
the device at these or any other conditions outside of those
listed in the operational sections of this specification is not
implied. Exposure to any absolute maximum rating for
extended periods may affect device performance and
reliability.
RELIABILITY CHARACTERISTICS
Symbol
Parameter
Reference Test Method
Min
Typ
NEND(3)
Endurance
MIL-STD-883, Test Method 1033 1,000,000
TDR(3)
Data Retention
MIL-STD-883, Test Method 1008
100
VZAP(3)
ESD Susceptibility MIL-STD-883, Test Method 3015
2000
ILTH(3)(4)
Latch-Up
JEDEC Standard 17
100
Max
Units
Cycles/Byte
Years
Volts
mA
D.C. OPERATING CHARACTERISTICS
V_CC = +1.8V to +6.0V, unless otherwise specified.
Symbol
Parameter
Test Conditions
ICC1
Power Supply Current
(Operating Write)
fSK = 1MHz
VCC = 5.0V
ICC2
Power Supply Current
(Operating Read)
fSK = 1MHz
VCC = 5.0V
ISB1
Power Supply Current
(Standby) (x8 Mode)
CS = 0V
ORG=GND
ISB2(5)
Power Supply Current
(Standby) (x16Mode)
CS=0V
ORG=Float or VCC
ILI
Input Leakage Current
VIN = 0V to VCC
ILO
Output Leakage Current
(Including ORG pin)
VOUT = 0V to VCC,
CS = 0V
VIL1
Input Low Voltage
4.5V ≤ VCC < 5.5V
VIH1
Input High Voltage
4.5V ≤ VCC < 5.5V
VIL2
Input Low Voltage
1.8V ≤ VCC < 4.5V
VIH2
Input High Voltage
4.8V ≤ VCC < 4.5V
VOL1
Output Low Voltage
4.5V ≤ VCC < 5.5V
IOL = 2.1mA
VOH1
Output High Voltage
4.5V ≤ VCC < 5.5V
IOH = -400µA
VOL2
Output Low Voltage
1.8V ≤ VCC < 4.5V
IOL = 1mA
VOH2
Output High Voltage
1.8V ≤ VCC < 4.5V
IOH = -100µA
Min
-0.1
2
0
VCC x 0.7
2.4
VCC - 0.2
Typ
Max
3
Units
mA
500
µA
10
µA
0
µA
1
µA
1
µA
0.8
V
VCC + 1
V
VCC x 0.2
V
VCC+1
V
0.4
V
V
0.2
V
V
Note:
(1) The minimum DC input voltage is –0.5V. During transitions, inputs may undershoot to –2.0V for periods of less than 20 ns. Maximum DC
voltage on output pins is V_CC +0.5V, which may overshoot to V_CC +2.0V for periods of less than 20 ns.
(2) Output shorted for no more than one second. No more than one output shorted at a time.
(3) This parameter is tested initially and after a design or process change that affects the parameter.
(4) Latch-up protection is provided for stresses up to 100 mA on address and data pins from –1V to V_CC +1V.
(5) Standby Current (ISB₂)=0µA (<900nA) for 93LC46/56/57/66, (ISB₂)=2µA for 93LC86.
Doc. No. 1023, Rev. G
2