RXM-900-HP3 Datasheet, PDF (2/13 Pages) List of Unclassifed Manufacturers – HP3 SERIES RECEIVER MODULE DATA

ELECTRICAL SPECIFICATIONS
Parameter
POWER SUPPLY
Operating Voltage
Supply Current
Power-Down Current
RECEIVE SECTION
Receive Frequency Range
Center Frequency Accuracy
Channel Spacing
First IF Frequency
Second IF Frequency
Noise Bandwidth
Data Rate
Analog / Audio Bandwidth
Analog / Audio Output Level
Data Output:
Logic Low
Logic High
Output Impedance
Data Output Source Current
Receiver Sensitivity
RSSI:
Dynamic Range
Gain
Voltage With No Carrier
Spurious Emissions
Interference Rejection:
FC±1MHz
FC±5MHz
ANTENNA PORT
RF Input Impedance
TIMING
Receiver Turn-On Time:
via V_CC
via PDN
Channel Change Time
Max time between transitions
ENVIRONMENTAL
Operating Temperature Range
Designation Min.
V_CC
I_CC
I_PDN
F_C
–
N_3DB
–
–
2.8
16.0
–
902.62
-50
–
–
–
–
100
50
0.8
–
0.0
–
V_CC-0.3
–
–
-94
60
–
–
–
–
–
R_OUT
–
T4
–
T3
–
T2
–
T1
–
–
-30
Table 1: HP3 Series Receiver Specifications
Notes
1. Over the entire operating voltage range.
2. With the PDN pin low.
3. Serial mode.
4. Characterized, but not tested.
5. With 1kHz sine wave @ 115kHz transmitter deviation
6. No load.
7. With 1V output drop.
8. For 10^-5 @ 9,600bps.
9. At specified center frequency.
Page 2
Typical
3.0
19.0
5.6
–
250
34.7
10.7
280
–
–
1.1
–
–
17
230
-100
70
24
–
-57
54
57
50
–
–
–
–
–
Max.
13.0
21.0
10.0
927.62
+50
–
–
–
–
56,000
28,000
2.0
0.5
V_CC
–
–
-107
80
–
1.6
–
–
–
–
7.0
3.0
1.5
20
+85
Units Notes
VDC
–
mA
1
µA
2
MHz
3
kHz
kHz
3
MHz
4
MHz
4
kHz
–
bps
–
Hz
4
VAC
5
VDC
6
VDC
6
kohms
–
µA
7
dBm
8,9
dB
4
mV/dB
4
V
4
dBm
4
dB
4
dB
4
Ω
4
mSec
4
mSec
4
mSec
4
mSec
4
°C
4
ABSOLUTE MAXIMUM RATINGS
Supply Voltage V_CC
Any Input or Output Pin
Operating Temperature
Storage Temperature
Soldering Temperature
-0.3
to +18.0
-0.3
to
V_CC
-30
to
+85
-45
to
+85
+260°C for 10 seconds
VDC
VDC
°C
°C
*NOTE* Exceeding any of the limits of this section may lead to permanent
damage to the device. Furthermore, extended operation at these maximum
ratings may reduce the life of this device.
PERFORMANCE DATA
These performance parameters
are based on module operation at
25°C from a 3.0VDC supply unless
otherwise noted. Figure 2
illustrates the connections
necessary for testing and
operation. It is recommended all
ground pins be connected to the
ground plane. The pins marked NC
have no electrical connection.
PC
PC
PC
5VDC
PC
ANT
NC
GND
NC
GND
NC
GND
NC
GND
NC
GND
NC
GND
NC
GND
NC
NC
NC
CS0
NC
CS1 / SS CLOCK NC
CS2 / SS DATA
NC
PDN
NC
RSSI
NC
MODE
NC
VCC
NC
AUDIO
NC
DATA
NC
Figure 2: Test / Basic Application Circuit
TYPICAL PERFORMANCE GRAPHS
PDN
1
RX DATA
2
CH1 1.00V
CH2 2.00V
500uS
Delta 1.920mS
Figure 3: RX Enabled to Valid Data
1 _{CH1 500mV}
1mS
Delta 4.080mS
Figure 5: Worst Case RSSI Response Time
3.0
2.5
2.0
1.5
1.0
-110 -100 -90
-80
-70
-60
-50
-40
RF INPUT (dBm)
Figure 4: Receiver RSSI
10^-6
10^-5
BER
10^-4
10^-3
-92 -93 -94 -95 -96 -97 -98 -99 -100 -101 -102
PIN (dBm)
Figure 6: BER vs. Input Power (typical)
Page 3