EN25B16 Datasheet, PDF (35/36 Pages) Eon Silicon Solution Inc. – 16 Mbit Serial Flash Memory with Boot and Parameter Sectors

Revisions List
EN25B16
Revision No Description
Date
A
Initial Release
2006/05/25
B
1. Add 16 pin SOP 300mil body width for package options in 2006/08/08
page 1
2. Add 16 pin SOP 300mil diagram in Figure 1
3. _{Add INSTRUCTIONS description in page 10}
4. Add figure 26 of SOP 300mil package
5. Add 16 pin SOP package option ‘F’ to ordering information
C
1. _{Change clock rate from 50MHz to 75MHz,}
2006/12/22
Page program time 1.4 ms typical to 1.5 ms typical
Sector erase time 100 to 300 ms typical to 300 to 800 ms
Chip erase time 10 seconds to 18 seconds typical
in page 1
2. Change Table 8 DC Characteristics in page 24
(1) Add ICC3 for 75MHz
3. Change Table 10 to 75MHz AC Characteristics in page 25
(1) Change F_R from 50 to 75MHz
(2) Change f_R from 33 to 50MHz
(3) Change t_CLH from 9ns to 6ns
(4) Change t_CLL from 9ns to 6ns
(5) Change t_SHQZ from 9ns to 6ns
(6) Change t_HLQZ from 9ns to 6ns
(7) Change t_HHQZ from 9ns to 6ns
(8) Change t_CLQV from 9ns to 6ns
(9) Change Page program time 1.4ms typical to 1.5ms
(10) Change 64KB Sector erase time 0.3 / 0.6 seconds to
0.8 / 2 seconds for typical and maximum
(11) Change 16KB Sector erase time 0.15 / 0.3 seconds to
0.5 / 1 seconds for typical and maximum
(12) Change 4KB Sector erase time 0.1 / 0.2 seconds to
0.3 / 0.6 seconds for typical and maximum
(13) Change Chip erase time 10 / 20 seconds to 18 / 35
seconds for typical and maximum
4. Add Table 11: 50MHz AC Characteristics in page 26
(1) Change Page program time 1.4ms typical to 1.5ms
(2) Change 64KB Sector erase time 0.3 / 0.6 seconds to
0.8 / 2 seconds for typical and maximum
(3) Change 16KB Sector erase time 0.15 / 0.3 seconds to
0.5 / 1 seconds for typical and maximum
(4) Change 4KB Sector erase time 0.1 / 0.2 seconds to
0.3 / 0.6 seconds for typical and maximum
(5) Change Chip erase time 10 / 20 seconds to 18 / 35
seconds for typical and maximum
5. Add 75MHz option in Ordering Information in page 33
6. _{Change Table 8. DC Characteristics VIL Max 0.3 VCC to 0.2}
V_CC in page 24
D
1. Change clock rate from 75MHz to 100MHz in page 1
2007/05/11
2. _{Change Table 7 Write Inhibit Voltage (Max) from 2V to 2.5V}
in page 23
3. ^{Add Table 10: 100MHz AC Characteristics in page 25}
This Data Sheet may be revised by subsequent versions ₃₅ ©2004 Eon Silicon Solution, Inc., www.essi.com.tw
or modifications due to changes in technical specifications.
Rev. C, Issue Date: 2006/12/22