MB9D560 Datasheet, PDF (44/91 Pages) SPANSION – This document states the current technical specifications regarding

MB9D560 Series
11. Electrical Characteristics
11.1 Absolute Maximum Ratings
Parameter
Power supply voltage^{*1, *2}
Analog power supply voltage^{*1, *2}
Analog reference voltage^*1
Input voltage^*1
Analog pin input voltage^*1
Input voltage^*1
Analog pin input voltage^*1
Output voltage^*1
Max clamp current
Max total clamp current
"L" level Max output current^*3
"L" level average output current^*4
"L" level total output current^*5
"H" level Max output current^*3
"H" level average output current^*4
"H" level total output current^*5
Power consumption
Operating temperature
Storage temperature
Symbol
V_CC
V_DD
AV_CC
RV_CC
AVRH
RVRH
V_I
V_IA
V_O
I_CLAMP
|I_CLAMP|
I_OL1
I_OL2
I_OL3
I_OLAV1
I_OLAV2
I_OLAV3
I_OL
I_OH1
I_OH2
I_OH3
I_OHAV1
I_OHAV2
I_OHAV3
I_OH
P_D
T_A
T_stg
Min
V_SS-0.3
V_SS-0.3
V_SS-0.3
V_SS-0.3
V_SS-0.3
V_SS-0.3
V_SS-0.3
V_SS-0.3
V_SS-0.3
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-40
-55
Rating
Max
V_SS+6.0
V_SS+1.8
V_SS+6.0
V_SS+6.0
V_SS+6.0
V_SS+6.0
V_CC+0.3
V_CC+0.3
V_CC+0.3
4
20
3.5
7
14
1
2
4
40
-3.5
-7
-14
-1
-2
-4
-40
1500
+125
+150
Unit
V
V
V
V
V
V
V
V
V
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mW
C
C
Remarks
AV_CCV_CC
RV_CCV_CC
AVRHAV_CC
RVRHRV_CC
*8
*8
When setting to 1 mA^*6
When setting to 2 mA
When setting to 4 mA^*7
When setting to 1 mA^*6
When setting to 2 mA
When setting to 4 mA^*7
*6
When setting to 1 mA^*6
When setting to 2 mA
When setting to 4 mA^*7
When setting to1 mA^*6
When setting to 2 mA
When setting to 4 mA^*7
*6
*9
*1: These parameters are based on the condition that V_SS=AV_SS=0.0V.
*2: Caution must be taken that AV_CC does not exceed V_CC.
*3: The maximum output current is defined as the value of the peak current flowing through any one of the corresponding pins.
*4: The average output current is defined as the value of the average current flowing through any one of the corresponding pins for a
10 ms period. The average value is the operation current  the operation ratio.
*5: The total output current is defined as the maximum current value flowing through all of corresponding pins.
*6: Corresponding pins: general-purpose ports
*7: Corresponding pins: general-purpose ports of P325 to P330
*8: Corresponding pins: all general-purpose ports and analog input pin
• Use the devices within recommended operating conditions.
• Use the devices with direct voltage (current).
• The + B signal should always be applied by connecting a limiting resistor between the + B signal and the microcontroller.
• The value of the limiting resistor should be set so that the current input to the microcontroller pin does not exceed rated values at
any time regardless of instantaneously or constantly when the + B signal is input.
• Note that when the microcontroller drive current is low, such as in the low-power consumption modes, the + B input potential can
increase the potential at the VCC pin via a protective diode, possibly affecting other devices.
• Note that if the + B signal is input when the microcontroller is off (not fixed at 0V), since the power is supplied through the pin,
the microcontroller may operate incompletely.
• Note that if the +B signal is input at power-on, since the power is supplied through the pin, the power-on reset may not function
in the power supply voltage.
• Do not leave + B input pins open.
Document Number: 002-05679 Rev.*A
Page 44 of 91